Samsung SCX-4100 specifications Not working with the message insufficient printer

Page 90

Troubleshooting

7.6.2 The printer is not working (2)

• Description

After receiving the print command there is no response at all or print speed is low

due to wrong setup of the environment rather than malfunction of the printer itself.

 

 

 

 

 

Check and Cause

Solution

 

 

1. Ensure you have sufficient free hard disk space for the

1. Not working with the message 'insufficient printer

temporary work files created during printing.

memory' means there is a hard disk space problem

 

 

rather than a printer RAM problem. In this case pro-

 

 

vide more space on the hard disk. Secure more

 

 

space using the disk utilities program.

2. Printing error occurs even if there is enough space in

2. The connection of the cable and printer port is not

the hard disk.

 

correct. Check that the cable is properly connected

 

 

and if you are using the parallel port check that the

 

 

port settings in CMOS is correct.

3. Check the parallel-port-related items in the CMOS

3. For the printer port, Select ECP. SPP and normal

Setup.

 

normal modes support 8-bit data transfer, while

 

 

ECP Mode supports 12-bit data transfer.

4. Reboot the system to print.

4. If the regular font is not printing, the cable or the

 

 

printer driver may be defective.

 

 

Turn the PC and printer off, and reboot the system

 

 

to print again. If not solved, double-click the printer

 

 

in my computer If the regular fonts are not printed

 

 

this time again. the cable must be defective so

 

 

replace the cable with new one.

 

 

 

Service Manual

7-25

Samsung Electronics

Page 89 Page 91
Image 90
Page 89 Page 91
Contents Troubleshooting PrecautionsSpecifications Block DiagramHttp//itself.sec.samsung.co.kr Precautions Safety WarningElectric Shock and Fire Safety Precautions Toxic materialHandling Precautions Assembly / Disassembly PrecautionsBe careful with the high temperature part Disregarding this warning may cause bodily injuryESD Precautions Tool for Troubleshooting Acronyms and Abbreviations IPC Select a location for the printer Sample Pattern for the Test 1 A4 5% Pattern2 A4 2% Pattern 3 A4 IDC 5% Patten Memo Specifications General SpecificationsPrint Specification Scan SpecificationCopy Specification CopyPaper Handiling Specification Other Specification WhqlMemo Printer Components Front ViewRear View Control Panel System Layout Drive Ass’y Paper Feed MechanismTransfer Ass’y Fixing PartFuserScan Image Controller Safety Relevant FactsScanner Unit CIS Driver CircuitLSU Laser Scanner Unit Toner Cartridge Main PBA Sdram Asic Chorus2Flash Memory Sensor input circuitCover Open Sensing Paper Feeding, Toner Cartridge SensingPaper Exit Sensing DC FAN / Solenoid DriverSmps & Hvps HVPSHigh Voltage Power Supply Consumption Power Smps Switching Mode Power SupplyRated Power Output Length of Power Cord 1830 ± 50mm Power Switch FittedEnvironment Condition Fuser AC Power ControlFeature Safty RequrementTransfer Engine F/WDrive FeedingFusing 5 LSUHeat Lamp Method Memo General Precautions on Disassembly Releasing Plastic LatchesWhenever servicing the machine, you must perform as follows Front and Rear Cover Units Side Covers Scanner Ass’y Remove Scanner Ass’yDismantle Scanner Ass’y Spring Pulley Idle ETC Belt Middle Cover FuserHeat Lamp Type Remove 4 screws and divide the Fuser into two parts Exit Roller LSUFan Engine Shield Ass’y Smps Transfer Roller Feed Roller Remove the Feed Roller and Feed Roller1, as shown below Pick Up Roller & Solenoid Memo Diagnostic Engine Test ModeTo enter the Engine Test Mode To enter the Engine Test modePaper Path Clearing Paper Jams Paper TrayPaper Exit Area Fuser Area or Around the Toner Cartridge Manual FeederPrinting the System Data List Clearing the MemoryClearing the Drum Consumables and Replacement Parts LCD Status Display by Each ErrorPeriodic Defective Image Roller Defective image Typical defectPrinting Problems Causes and Solutions Vertical Black Lines and BandsVertical White Line Horizontal Black Bands Black/White SpotLight Image Dark Image or a BlackUneven Density BackgroundGhost Stains on the Face Digital Printer GhostStains on Back Blank Page Print outCopy Problems White CopyBlack Copy Abnormal noise Defective Image QualityPaper Feed problems Causes and Solutions Wrong Print Position2 JAM 3 JAM 4 JAMMulti-Feeding Paper rolled in the fuserPaper rolled on the OPC Drum Printer Faults Causes and Solutions Fuser ErrorLSU Error Fuser gear melts due to overheating causing Paper Jam Paper EmptyPaper Empty without indication Cover OpenNo error message when the cover is open No Power Defective motor operationPrinted Vertical Lines become curved Service for the Life of Toner Cartridge Toner Cartridge ServicePrecautions on Safe-keeping of Toner Cartridge Standard of guarantee for consumable partsSigns and Measures of Poor toner cartridge EndedFault Signs Cause & Check Solution Fault Signs Cause & Check Solution Ghost & Image Software Problems Causes and Solutions Printer is not workingNot working with the message insufficient printer Abnormal Printing Spool Error How to delete the data in the spool managerMemo Exploded Views and Parts List Main Assembly Main Assembly Parts List Frame Assembly Frame Unit Assembly Parts List Description SEC.Code ’ty RemarkFrame Unit Assembly Parts ListCont Scanner Unit Assembly Scanner Unit Assembly Parts List Fuser Unit Assembly Fuser Unit Assembly Parts List WASHER-PLAIN Middle Cover Unit Assembly Middle Cover Unit Assembly Parts List ’ty RemarkDrive Unit Assembly Drive Unit Assembly Parts ListCassette Unit Assembly Cassette Unit Assembly Parts List Block Diagram 10.10Connection Diagram
Related manuals
Manual 169 pages 2.29 Kb Manual 167 pages 32.6 Kb
Top Page Image Contents