Samsung SCX-4100 specifications Copy Problems, White Copy, Black Copy

Page 73

Troubleshooting

7.2 Copy Problems

7.2.1 White Copy

•Description Blank page is printed out when copying.

	Check and Cause		Solution

1.	Check the Scanner Cover is properly closed.	1.	Room light can pass through a thin original.
2.	Check shading profile.	2.	Redo shading profile in the tech mode.
3.	Check white/black reference voltage on Main PBA. e.q	3.	Replace CN7 if it is defective.
	• CIS_SI, CIS_CLK at CN7		• CN7-Pin6(CIS-SI)
	• Or Check the FFC		• CN7-Pin7(CIS-CLK)

7.2.2 Black Copy

•Description Black page is printed out when Copying.

	Check and Cause		Solution

1.	Check for CIS problem on the Main PBA.	1.	Check the CIS harness is properly connected.
2.	Check shading profile.	2.	Redo shading profile in the tech mode.

Service Manual

7-8

Samsung Electronics

Image 73

Contents Specifications PrecautionsTroubleshooting Block DiagramHttp//itself.sec.samsung.co.kr Safety Warning PrecautionsToxic material Electric Shock and Fire Safety PrecautionsAssembly / Disassembly Precautions Handling PrecautionsDisregarding this warning may cause bodily injury Be careful with the high temperature partESD Precautions Tool for Troubleshooting Acronyms and Abbreviations IPC Select a location for the printer 1 A4 5% Pattern Sample Pattern for the Test2 A4 2% Pattern 3 A4 IDC 5% Patten Memo General Specifications SpecificationsScan Specification Print SpecificationCopy Copy SpecificationPaper Handiling Specification Whql Other SpecificationMemo Front View Printer ComponentsRear View Control Panel System Layout Transfer Ass’y Paper Feed MechanismDrive Ass’y Fixing PartFuserScanner Unit Safety Relevant FactsScan Image Controller CIS Driver CircuitLSU Laser Scanner Unit Toner Cartridge Main PBA Flash Memory Asic Chorus2Sdram Sensor input circuitPaper Exit Sensing Paper Feeding, Toner Cartridge SensingCover Open Sensing DC FAN / Solenoid DriverSmps & Hvps HVPSHigh Voltage Power Supply Rated Power Output Smps Switching Mode Power SupplyConsumption Power Length of Power Cord 1830 ± 50mm Power Switch FittedFeature Fuser AC Power ControlEnvironment Condition Safty RequrementDrive Engine F/WTransfer Feeding5 LSU FusingHeat Lamp Method Memo Releasing Plastic Latches General Precautions on DisassemblyWhenever servicing the machine, you must perform as follows Front and Rear Cover Units Side Covers Remove Scanner Ass’y Scanner Ass’yDismantle Scanner Ass’y Spring Pulley Idle ETC Belt Middle Cover FuserHeat Lamp Type Remove 4 screws and divide the Fuser into two parts LSU Exit RollerFan Engine Shield Ass’y Smps Transfer Roller Feed Roller Remove the Feed Roller and Feed Roller1, as shown below Pick Up Roller & Solenoid Memo To enter the Engine Test Mode Engine Test ModeDiagnostic To enter the Engine Test modePaper Path Paper Tray Clearing Paper JamsPaper Exit Area Manual Feeder Fuser Area or Around the Toner CartridgeClearing the Memory Printing the System Data ListClearing the Drum LCD Status Display by Each Error Consumables and Replacement PartsRoller Defective image Typical defect Periodic Defective ImageVertical Black Lines and Bands Printing Problems Causes and SolutionsVertical White Line Black/White Spot Horizontal Black BandsDark Image or a Black Light ImageBackground Uneven DensityGhost Digital Printer Ghost Stains on the FaceBlank Page Print out Stains on BackWhite Copy Copy ProblemsBlack Copy Defective Image Quality Abnormal noiseWrong Print Position Paper Feed problems Causes and Solutions2 JAM 4 JAM 3 JAMPaper rolled in the fuser Multi-FeedingPaper rolled on the OPC Drum Fuser Error Printer Faults Causes and SolutionsLSU Error Paper Empty Fuser gear melts due to overheating causing Paper JamCover Open Paper Empty without indicationNo error message when the cover is open Defective motor operation No PowerPrinted Vertical Lines become curved Precautions on Safe-keeping of Toner Cartridge Toner Cartridge ServiceService for the Life of Toner Cartridge Standard of guarantee for consumable partsEnded Signs and Measures of Poor toner cartridgeFault Signs Cause & Check Solution Fault Signs Cause & Check Solution Ghost & Image Printer is not working Software Problems Causes and SolutionsNot working with the message insufficient printer Abnormal Printing How to delete the data in the spool manager Spool ErrorMemo Exploded Views and Parts List Main Assembly Main Assembly Parts List Frame Assembly Description SEC.Code ’ty Remark Frame Unit Assembly Parts ListFrame Unit Assembly Parts ListCont Scanner Unit Assembly Scanner Unit Assembly Parts List Fuser Unit Assembly Fuser Unit Assembly Parts List WASHER-PLAIN Middle Cover Unit Assembly ’ty Remark Middle Cover Unit Assembly Parts ListDrive Unit Assembly Parts List Drive Unit AssemblyCassette Unit Assembly Cassette Unit Assembly Parts List Block Diagram 10.10Connection Diagram

Related manuals

Manual 169 pages 2.29 Kb

Manual 167 pages 32.6 Kb