Mitsubishi Electronics LT-46244, LT-52244 manual Receiver Sound System, Older Cable Box

Page 26

263. TV Connections

A/V Receiver (Sound System)

Most setups require either a digital audio cable or analog stereo audio cables.

The TV makes all audio available in digital and analog formats:

Analog audio coming into the TV is output in digital stereo format on the DIGITAL AUDIO OUTPUT jack (TV back panel #2).

Digital incoming audio is available as analog output on the AVR AUDIO OUTPUT, L and R jacks (TV back panel #1).

Usually, only one of the following connections is required:

To connect an analog A/V receiver

Connect left (white) and right (red) audio cables from AVR AUDIO OUTPUT, L and R on the TV back panel #1 to the TV AUDIO INPUT on the A/V receiver.

To connect a digital A/V receiver with Dolby Digital surround sound and PCM audio support: Connect one end of the digital audio cable to DIGITAL AUDIO OUTPUT on the back of the TV (back panel #2). Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.

%JHJUBM$PBYJBM$BCMF

6TFUPDPOOFDUB

EJHJUBM"7SFDFJWFS 4UFSFP"OBMPH$BCMFT 6TFUPDPOOFDUBO BOBMPH"7SFDFJWFS

57#BDL1BOFM

"/5."*/

34

"!#+ ).054 0!.%, 

3

-

 

 

BELOWWLABEL WITHINIRECESSEDSAREA ATTTOP

 

 

"73

"6%*0065165

57#BDL1BOFM

Figure 11. Connecting the TV to an A/V receiver

Important

A/V Receivers with HDMI Inputs

If your A/V receiver has an HDMI input, use one of the audio connections described here instead of an HDMI connection.

Note:

On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. To hear these copy- protected signals through the A/V receiver, use connections for analog A/V receivers.

Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

Older Cable Box

Required: One coaxial cable.

Note: This connection is not recommended. The other connections described in this chapter provide better quality audio and video to the TV and allow NetCommand to work with the cable box.

1.Connect the incoming cable to IN on cable box.

2.Connect one coaxial cable from OUT on the cable box to ANT 1/MAIN on the TV back panel.

"/5."*/

"!#+ ).054 0!.%, 

BELOWWLABEL WITHINIRECESSEDSAREA ATTTOP

57#BDL1BOFM

5P"/5."*/

$BCMF#PY

065

*/

Figure 12. Connecting an older cable box

Image 26
Contents LT-46244 LT-52244 Refer Servicing to Qualified Service Personnel For Your RecordsContents Cleaning Recommendations Installation NotesTV Guide Daily Access Requirements If Your TV Gets DamagedImportant Safeguards Package Contents Special Features of Your TVSwivelling Stand Indicator LightsTV Front Panel TV Guide Daily Interactive Program GuideTV Side Panel System Reset ButtonReset Side Panel Input JacksComponent Inputs Audio and Video TV Back PanelANT 1/MAIN, ANT 2/AUX Antenna RS-232 Port CableCARD Slot IR Emitter NetCommandHdmi Inputs Input 1, 2 Audio and VideoWall Mount Kit purchased separately Stand Removal ProcedureStand Removal Instructions Getting Started Guidelines for Setting Up and Using Your New Widescreen TVAdditional TV Setup TV OperationInitial TV Setup Installing the Remote Control BatteriesWhen You First Power On the TV When You First Connect a Device Setting Up TV InputsAdditional TV Setup Using the Setup Menu Change the Menu LanguageWith NetCommand Control of an A/V Receiver Controlling A/V Receiver Sound VolumeWith a Standard TV Setup More About Auto Input SensingCableCARD menu Network Setup Using a CableCARDInstalling a CableCARD Displaying CableCARD InformationThis TV accepts digital computer signals only Using the TV with a Personal ComputerConnecting a Computer to the TV Computer Video Connection Audio Video OutputComputer Display Formats Computer Video AdjustmentsImage Resolution Before you Begin Cable ManagementHdtv Cable Box or Satellite Receiver with Component Video TV Connections Antenna with a Single Lead Direct Cable no cable boxAntennas with Separate UHF and VHF Leads Can be used with a CableCARDDVD Player with Component Video %1MBZFS 57#BDL1BOFMVCR to an Antenna or Wall Outlet Cable Connecting a VCR to a cable box VCR to a Cable Box Audio & VideoTo connect an analog A/V receiver Receiver Sound SystemOlder Cable Box Receivers with Hdmi InputsComponent Y Pb Pr Video Connection CamcorderComposite Video Connection Hdmi ConnectionTV Tips Sleep TimerChoosing a Viewing Source Remote Control Adjust Up/Down/Left/Right Navigate menus and change settingsLow-Battery Indicator NetCommand for Hdmi DevicesResetting the Remote Control Care of the Remote ControlChannelView Channel Listings Using ChannelViewFeature Press KeyAnt 1 Signal StrengthStatus Display Monday Night FootballFav Favorite Channels ANT-1DVD Image Definitions TV Signals and Display FormatsSignal Definitions TV Display Format DefinitionsViewing Camera Files Jpeg Photos and the USB Photo PortSlide Show Media Setup MenuPhotos and Moving Video as Composite Video Keys for Jpeg Picture Slide ShowRemote Control Keys for the TV Menu System Main MenuAV Menu AV Menu OptionsVideo Menu Video Menu OptionsANT1/ANT2 SAP Audio MenuAudio Menu Options ANT1/ANT2Captions on Digital Channels Captions MenuCaptions on Analog Channels Captions Menu OptionsSetup Menu Setup Menu OptionsSetup menu, Edit channel options Select either Applies or Ignore for Daylight Savings Time SettingsClock Energy Fast Power On TimerTimer On, Off Day Mode Low PowerVCR, PC Inputs MenuInputs Menu Options AVRInputs Guide menu for TV Guide Daily setup Setting Up TV Guide DailyUsing TV Guide Daily Parent Menu Lock MenuPass Codes Other Menu Alternate Rating SystemTV-Y7 Parent Menu Options U.S.-based rating systemTV-Y TV-GSide Panel Other Menu Options alternate rating systemTime About NetCommand Important Note on NetCommandIR Emitter Placement Connecting IR Emitter NetCommandInitial NetCommand Setup for Most Devices If the device has no Power OFF key, skip this stepCH/PAGE PowerGuide Special Operation Methods To Control an A/V Receiver Operating NetCommand-Controlled DevicesTo Control Most Device Types Inside the Guide Outside the GuideSetting Up NetCommand Control of an A/V Receiver Before You Begin Joqvu Appendix B Specifications Appendix C TV Guide Daily Appendix E TroubleshootingAppendix a Bypassing the Parental Lock Bypassing the Parental LockThis page intentionally left blank Appendix B Specifications ModelMain Guide Screen Elements Initial Guide SetupAppendix C TV Guide Daily Customize Guide Listings Accessing Ad InformationNavigating the Guide Available Options Modify Guide SetupProcedure TV Guide Daily Troubleshooting Tips Symptom Remarks Appendix D Programming the Remote Control Functions Available for Other A/V DevicesAudio Lock Universal A/V Receiver Control Programming the Remote ControlCode Verification Programming Codes Audio Amplifiers Brand CodeCD Players Brand Code Cable Boxes Brand CodeDVD Players/Recorders Brand Code TFCLaser Disc Players Brand Code Satellite Receivers Brand CodeVCRs and DVRs Brand Code ABSAppendices75 Reset Name When to Use How to Use Resulting Action Appendix E TroubleshootingTV Reset Comparison Guide Read the ON-SCREEN Service and SupportService TionsGeneral TV Operation Symptom Remarks TV Channels Symptom RemarksTV Power On/Off Symptom Remarks Picture Symptom RemarksSymptom Remarks Indicators Symptom RemarksNetCommand Symptom Remarks HdmiTrademark and License Information Mitsubishi TV Software To Obtain Warranty Service This Limited Warranty does not CoverMitsubishi Digital Electronics AMERICA, INC Index Index87 MDEAservice@mdea.com System Reset