Mitsubishi Electronics 154 manual Programming the Remote Control, Code Verification

Page 74

74Appendices

Appendix A: Programming the Remote Control, continued

Programming the Remote Control

1.Press one of the upper buttons on the remote control to change to the correct mode for the product you want to control. Refer to the table below. Only one of each device type can be con- trolled in each mode.

Mode

Affected Device

Cab/SAT

Cable Box

 

DTV Receiver

 

Satellite Receiver

 

 

VCR

VCR

 

DVR

 

DVD Player/Recorder

 

 

DVD

DVD Player/Recorder

 

DVR

 

VCR

 

 

Audio

A/V Receiver

 

Audio Amplifier

 

CD Player

 

 

2.Press and hold POWER on the remote control for several seconds until the key blinks twice and goes off.

3.Release the POWER key.

4.Enter the first five-digit code listed for your equip- ment in the reference tables that follow.

If you need to start over or wish to exit programming mode, temporarily change to a different device mode.

5.Point the remote control at the equipment and press POWER. If the product has no power on/off

function, press a different key, such as (Play),

(Stop), VOLUME UP, or MUTE.

If the equipment responds, the remote control is properly programmed.

If the equipment does not respond, repeat steps 4 and 5 with the next five-digit code listed for your equipment.

6.Once you have found the correct code, write it in the space below for future reference.

Mode

Device Type

Code

CABLE/SAT

 

 

 

 

 

VCR

 

 

 

 

 

DVD

 

 

 

 

 

AUDIO

 

 

 

 

 

IMPORTANT

You may need to reprogram the remote control after changing the batteries. Record the codes for each mode in the space provided to make this faster.

Code Verification

To determine the code programmed for any mode:

1.Set the mode to the one you wish to verify.

2.Press and hold POWER on the remote control for several seconds until the key blinks twice and goes off.

3.Press keys 9 9 0

4.Press 1 and count the blinks of the power key. Write down the number of blinks as the first digit of the code.

5.Repeat step 4 for the second, third, fourth, and fifth digits of the code.

Audio Lock: Universal A/V Receiver Control

With Audio Lock enabled, the remote control oper- ates volume and mute on an A/V receiver in all control modes. Activate Audio Lock if you always use an A/V receiver with your TV and other A/V equipment.

1.Program AUDIO mode for your A/V receiver as described in “Programming the Remote Control” on this page.

2.With the remote control in AUDIO mode, hold POWER on the remote control for several seconds until the key blinks twice and goes off.

3.Press keys 9 9 3 ENTER

The POWER key will blink twice to indicate Audio Lock is active.

To Reset the Remote Control to Operate Volume and Mute for the TV Speakers

1.Press and hold POWER for several seconds until it blinks twice and goes off.

2.Press keys 9 9 3 VOLUME UP.

The POWER key will blink four times to indicate Audio Lock has cleared.

For assistance call 1(800) 332-2119

Image 74
Contents Series FCC Declaration of Conformity Contents Installation and Operating Notes Important Information About Your TVReplacement Parts Outdoor Antenna GroundingStand Installation BackWall-Mounting Stand Removal Prior to Wall-MountingSpecial Features of Your TV Package Contents Installing the Remote Control BatteriesTV Tips Before You Begin First-Time Power-OnControlling Sound Volume Turning the TV On or OffRemote Control TV ControlsPicture Sound Tools Key and MenuTools Picture Advanced menu, selectTV Control Panel Power IndicatorSystem Reset Panel-Lock ReleaseSetting Up Inputs with Auto Input Sensing Setting Up TV InputsUsing the ANT Antenna Input Memorizing Channels with Channel Scan For the ANT inputAuto Input Sensing for Most Devices When You First Connect a DeviceAbout Auto Input Sensing Tips on Auto SensingSelecting an Input to Watch CancelBasic TV Operation Watching Broadcast TVTV Care Picture SettingsBasic Audio Controls AssistanceFormat Key and Picture Shape More TV FeaturesFeature Input Selection menu Inputs Name menuDVI Video Connection Connecting a Computer to the TVHdmi Connection Compatible with VGA analogImage Resolution Using the TV with a Personal ComputerComputer Video Adjustments Computer Display FormatsConnection Types Before You BeginAuto Input Sensing Picture QualityOutput CENTER-CH Inputs and OutputsCable Routing LANHdmi Inputs High-Definition Multimedia Interface USB Power OnlyANT Antenna Video Composite VideoAny Hdmi device Hdmi and Digital Surround Sound Hdmi DeviceAuto Input Sensing DVI Video Device Incoming from cable service or satellite dishPb Pr Component Video Device Component video device Audio CablesComposite Video Device Antenna or Cable TV ServiceVCR or DVD Recorder to an Antenna or Wall Outlet Cable VCR or other device with composite video outputDVD player ReceiverReceiver with Hdmi Output Adding a Subwoofer Using the TV Speakers as a Center ChannelSupplemental Audio Connections Viewing or Changing the Sleep Timer Sleep TimerSetting the Sleep Timer FAV Favorite ChannelsChannelView Channel Listings Using ChannelView ListingsUsing Custom Channel Banks About ChannelViewAbout Channel Numbers Signal DefinitionsStatus Display Redirecting Audio Output Using an External Sound SystemControlling A/V Receiver Sound Volume Effect of Mitsubishi Formats on Picture Types Picture Shape and Display FormatsFormat Definitions DVD Image DefinitionsUSB Media Player Menu Camera Images and Music FilesUSB Source Devices Key For Photos or Audio Tracks Using the Photos and Audio MenusUSB Media Setup Menu Slideshow + Music --Slideshow only Music onlyOptional Using an Audio-Only DevicePhotos and Motion Video as Composite Video Unused 1. RCA-style plug Plug in firstResetting Bluetooth Pairing or Connection Wireless Audio PlaybackPairing the TV with an Audio Playback Device Tips for Wireless PlaybackSound Projector Technology Basic Manual SetupSound Projector Before You BeginAdjusting an External Subwoofer Adjusting Beam AnglesAdjusting Levels Start Auto Setup Auto SetupMicrophone Placement Initial PreparationSpeaker unit External Rear SpeakersTransmitter Polk Audio F/X Audio inputsEthernet Connection Home Network SetupStreamTV Internet Media @ # $ % * + = . space ? Wireless ConnectionKey Use for Using Vudu Apps and Vudu Movies Using StreamTV Internet MediaTroubleshooting Getting Started with Vudu MoviesSource device connected directly to the TV Introduction to Home-Theater ControlMain Menu PicturePicture Picture+ Using PerfecTint Picture ResetUsing PerfectColor Picture PerfectSound Sound AudioSound SoundPro Sound GlobalSound Auto SP SAPCaptions Setup Clock SetupSetup Language Setup TimerPhysical Digital Channel Number. Setup ChannelAdding/Deleting Channels Using the Channel Edit Menu Ethernet Connection Dhcp automatic, Manual Connection Data Setup EnergySetup Network Inputs InputsInputs Name Inputs ControlInputs Order Inputs DemoLock Lock Parental TV-YLock Panel Lock TimeLock Channel Lock OtherAbout NetCommand IR Control Important Note on NetCommandIR Emitters PlacementHighlight IR-NetCommand Output If You are Unable to Locate a Device’s IR SensorNetCommand and Device-Specific Keys NetCommand SetupInitial NetCommand Setup Adding or Removing Device Keys from NetCommand Control Controlling Most Device TypesSpecial Operation Methods Operating NetCommand-Controlled DevicesSpecial Operation Description and Setup How to Use Separator Cancel Cancel as the Cancel or Exit FunctionEnter digits Menu NetCommand Specialized Device KeysFav Favorites InfoControlling Other A/V Receiver Functions Switching Audio to and from the A/V ReceiverControlling A/V Receiver Power With Any Connection TypeSetup to Control A/V Receiver Power and Volume Setting Up A/V Receiver ControlPower and Volume Before You BeginPerform NetCommand setup Automatic Audio/Video Switching Over an Hdmi ConnectionMore About Using an Hdmi Connection Before You Begin Open the Inputs Learn menu Appendices Appendix a Programming the Remote Control Functions Available for Other A/V DevicesCode Verification Programming the Remote ControlAudio Lock Universal A/V Receiver Control Audio Amplifiers Audio AccessoriesVideo Accessories Satellite Receivers VCRsAppendices77 TAG Blu-ray and HD-DVDMitsubishi Home Theater TV Bypassing the Parental LockThis page intentionally left blank Has No Hdmi Control Option Appendix C Hdmi Control of CEC DevicesEnabling Hdmi Control of CEC Devices Hdmi cable cannot support CEC ActionHdmi Control of an Hdmi A/V Receiver and Connected Devices VCRUsing Hdmi Control Resolving CEC ConflictsAppendix D TV Care Cleaning RecommendationsCare of the Remote Control Service and Customer Support Appendix E TroubleshootingTV Reset Comparison Guide New Device Found screen See the Setup Channel EditIf the New Device Read the ON-SCREENGeneral TV Operation Symptom Remarks VuduTV Channels Symptom Remarks TV Power On/Off Symptom RemarksPicture Symptom Remarks Sound Symptom Remarks Check that Digital Audio Output and/or AVR/SURROUNDAppendices91 Trademark and License Information Mitsubishi TV Software END-USER License Agreement for Embedded SoftwareGNU General Public License Conveying Verbatim Copies Acceptance Not Required for Having Copies GNU General Public License Version 2, JuneNo Warranty This Limited Warranty does not Cover Mitsubishi LCD Flat Panel Hdtv Limited WarrantyTo Obtain Warranty Service Network Service Disclaimer WarrantyIndex HdmiIndex Page MDEAservice@mdea.com System Reset
Related manuals
Manual 104 pages 28.69 Kb