JVC GM-F470S, GM-F520S, GM-F420S specifications Daily Operations

Page 10

Daily Operations

Turning on the main power

On the top of

the rear panel

 

 

 

 

 

: Main power on

 

 

 

 

 

 

 

 

 

 

 

: Main power off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

On the bottom of the rear panel

 

 

 

 

 

 

 

 

 

Turning on the monitor

• To turn off the monitor, press POWER OFF.

On the main unit:

Each time you press the button, the power turns on and off.

Selecting an input

On the main unit:

Each time you press the button, the input changes.

Adjusting the volume

On the main unit:

To turn off the volume immediately:

• Pressing the button again resumes the previous volume level.

• Muting can also be activated on the main

Remote

menu (see “AUDIO SETTING” on page 13). control only

10

When the Control Lock is set to “ON” (see page 16), you cannot use the buttons on the main unit.

• When the Security Lock is set to “ON” (see page 17), a password entry screen of the set-up menu appears at turning on the power. Enter the correct password before starting operations.

Changing the aspect ratio

Each time you press the button, the aspect ratio changes as follows:

REGULAR

Displays at conventional 4:3 aspect ratio.

Remote sensor

FULL

Enlarges the picture of 4:3 aspect ratio horizontally.

• For the picture of 16:9 aspect ratio, the aspect ratio is not changed.

ZOOM

Enlarges the picture of 4:3 aspect ratio vertically and horizontally at the same ratio.

PANORAMIC

Enlarges the picture of 4:3 aspect ratio horizontally to the extent that the picture does not look abnormal.

REAL DOT

Displays the original picture input at the center without zooming.

This item is not available when UXGA (1600x1200) signal is input.

NOTE

• For some signals, the aspect ratio cannot be changed or some modes cannot be selected.

• While the Multi Display is in use (see page 14), the aspect ratio is fixed to “FULL.”

• While the Dual Display is in use (see page 11), the aspect ratio other than “REGULAR” is changed and fixed to “FULL”, and remains “FULL” even after you turn off the Dual Display.

• The aspect ratio can also be changed on the main menu (see “SIZE SETTING” on page 13).

Image 10
Contents GM-F520S GM-F470S GM-F420S Power Connection Safety PrecautionsHow to replace the fuse Screen MaintenanceDear Customer CabinetHow to attach the stand InstallationPrecautions To prevent an accidental fallParts Identification Remote controlMonitor Audio 1 OUT ConnectionsAudio 2 OUT Video output terminals Video input terminalsAudio input terminals Audio output terminalsVideo RGB DVI-D Available signalsVideo signals GNDComputer signals RGB DVI-DDaily Operations Activating the Dual Display Selecting the picture modeDisplaying the current status Controlling only the monitor with specified IDSelect an item by pressing 5 ∞ , then press Menu OperationDisplay the menu Menu Configuration-MAIN Menu Multi Size Color SystemMulti Display Dual DisplayMenu Configuration-SET-UP Menu Program SET Sunday Monday Subnet Mask Default Gateway DNS ServerPresent Time Tuesday WednesdaySetting the Security Lock Using the timerOutline of the motion sensor Installation and connectionAngle of the sensor Setting About the external control Remote in SEL CNT. RJ45 OUTUsing the serial communication To assign the functions to the pin terminals How to Use External ControlUsing the MAKE/TRIG. system OperationTo join the network Using the LAN systemOperation on the web browser General-Purpose Control Motion Sensor SettingFunction Aspect Direct Selection Full Troubleshooting Please Enter Pass ID Symptom Probable cause and corrective actionSetting Following are not malfunctionsSelf-diagnostic Report Sheet Self-diagnostic indicationIf the trouble still persists, follow the procedure below TEMP. OverSpecifications GeneralGM-F520S DimensionsInput/output terminals Motion sensorTop view Front view GM-F470SGM-F420S Rear viewPage Victor Company of Japan, Limited 0209TKH-MW-MT