Arcam AVR250 Saving Settings and Exit Set-up, ADV 4 Zone 2 Settings, ADV 5 Analogue Settings

Page 17

ADV 4 – Zone 2 Settings

ZONE2 VOL: Sets the volume for Zone 2.

Max Vol 20–83: Limits the maximum volume setting for Zone 2. This is a useful feature to prevent accidental overdriving of low power-handling speakers, for example.

Fix Vol: This selects between fixed and variable audio output to Zone 2. If NO is selected, the output level can be controlled from Zone 2 or the main system. If you wish to fix the volume level, first set the Zone 2 volume to the desired level, then select YES.

Max On Vol: Limits the maximum volume Zone 2 operates at when it is first switched on. Zone 2 comes on at this volume if the last used volume exceeds this value.

Stand-by: This allows zone 1 (the main zone) to be put into stand-by, either locally only or by Zone 2 as well.

n n

LOCAL ONLY: Only the main zone will be switched into stand-by from the main zone.

ALL OFF: Both the main zone and Zone 2 will be switched into stand-by from the main zone.

Access: This acts as a ‘parental control’ device to disable or enable access to sources for Zone 2.

Press the unwanted source button on the remote control handset or front panel to disable it for Zone 2. Press again to enable the source.

Enabled sources are listed on the ‘Access:’ line of the menu page.

Note: if a source is already in use in Zone 2 when access to it is removed, the source remains active until a different source is selected in that zone. After this time, the original source is unavailable.

ADV 5 – Analogue Settings

Input trims: Allows the adjustment of the input sensitivity of the analogue inputs (in Volts rms) so that each one achieves the optimum dynamic range and sounds similar in loudness to the others.

Available level settings are: LOW 0.5V, MEDIUM 1V, REFERENCE 2V, HIGH 4V. The reference level of 2V should be appropriate for most inputs.

If a source is very quiet compared with the other sources you can increase its loudness by selecting the MEDIUM 1V or LOW 0.5V settings.

Saving Settings and Exit Set-up

You can either save the settings now or exit without saving the changes.

Save Set-up

1.Press MENU to go to the ‘Set-up Menu Index’ at the ‘Save Set-up’ point.

2.Press OK to save.

3.Press OK to select ‘Exit Set-up’ and exit system configuration.

Exit without saving

If you choose to ‘Exit Set-up’ without first saving the changes, then the new settings will be lost.

1.Press MENU to go to the ‘Set-up Menu Index’ at the ‘Save Set-up’ point.

2.Press4to select ‘Exit Set-up’.

3.Press OK when ‘Exit Set-up’ is selected to exit system configuration.

AVR250

E-17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents AVR250 Safety compliance Safety guidelinesImportant safety instructions Contents Safety Using this handbookBefore you start IntroductionBefore making connections Inserting the batteries into the remote controlPositioning the unit InstallationAVR250 rear panel CablesAnalogue audio connections Audio connectionsSubwoofer output Connection of record decksVideo connections Scart RGB 4-WIRE ConnectionComposite/S-video video connections High quality Component video connectionsUsing bare wire ended leads Connecting loudspeakersUsing spade terminals Zone 2 connectionsConnecting to a power supply Connecting the AM and FM antennasSet-up mode Configuring the AVR250Set-up Menu Index Navigating the Set-up menu2/S-VIDEOtrigger is not active in this mode General Settings‘Basic’ Set-up Menus Select Cvbs statusSurr L/R Small Large Subwoofer SettingsSpeaker Sizes Distance measurements for 5.1 Speaker delay settings Speaker Delay SettingsEX Settings Level settingsTest Tone Cycle Use Channels 6+7 forADV 3 Digital Settings ADV 2 Video Settings‘Advanced’ Set-up Menus ADV 1 Speaker EqADV 4 Zone 2 Settings Saving Settings and Exit Set-upADV 5 Analogue Settings Save Set-upRemote control Volume control Switching on/offOperating your AVR250 Front panel displayInput selection HeadphonesStereo Direct ZoneEffects/FX Remote control buttonsMode Treble/BassTuning to a station Using the tunerStoring a preset Deleting a presetUsing the Main Menu Decoder splits the centre signal equally to Using ZoneIntroduction EffectDigital multi-channel sources Surround modesMulti-channel source modes Two-channel source modesDSP Effects Modes Speaker positioningBi-wiring your loudspeakers Bi-wiring and bi-amping loudspeakersBefore you start important information Bi-amping your systemTroubleshooting No Zone 2 audio when playing DTS film Source switching changes randomly or freezes on one sourceUnable to adjust bass and treble controls Hum on an analogue inputScart S-video cable with audio back to processor Scart connectionsScart RGB cable with audio back to processor IR Remote Codes Command Command codePreset System code Command Command codePower toggle Mute Preset/Tune down Preset/Tune up Preset/Tune mode toggleRadio interference Technical specificationsContinual improvement policy On line registration GuaranteeWorldwide Guarantee Appendix Serial programming interface Command and response formatsPower / Alimentation / Betriebsbereitschaft / Stroom Example / Exemple / Beispiel / Voorbeeld Mute / Coupure du son / Stumm / DempenChange l’entrée audio et vidéo d’une zone Changes the audio and video input to a zoneÄnderung des Audio- oder Videoeingangs einer Zone De audio- en video-ingang naar een zone wijzigenChange l’entrée vidéo de la zone principale Changes the video input for the main zoneÄnderung der Videoquelle der Hauptzone De video-ingang voor de hoofdzone wijzigenDirect mode / Mode Direct / Direktmodus / Modus Direct Navigation / Navigation / Navigation / Navigatie Effect / Effet / Effekt / EffectStore / Mémorisation / Speichern / Opslaan Preset / Présélection / Voreinstellung / VoorinstellingRDS / Système RDS / RDS / RDS Tune / Réglage / Senderabstimmung / Afstemmen
Related manuals
Manual 44 pages 3.26 Kb Manual 44 pages 59.25 Kb

AVR250 specifications

The Arcam AVR250 is a distinguished model in the realm of home theater receivers, embodying high-performance audio and video processing capabilities that cater to discerning audiophiles and home cinema enthusiasts alike. Designed by Arcam, a company renowned for its commitment to delivering premium sound, the AVR250 stands out through its thoughtful engineering and robust feature set.

At the heart of the AVR250 lies a powerful amplification stage capable of delivering a peak output of 100 watts per channel into 8 ohms, ensuring that even the most demanding speakers can be driven with ease. This level of power translates into dynamic audio experiences, whether you're enjoying your favorite movies, music, or gaming. The receiver also incorporates a sophisticated digital signal processing engine that enhances sound quality and ensures accurate reproduction of all audio formats.

One of the standout features of the AVR250 is its support for multiple surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II. This enables users to experience surround sound in its full glory, bringing their favorite films to life with immersive audio tracks that add depth and realism to the viewing experience. The AVR250 also boasts an array of connectivity options, including HDMI inputs that support high-definition video and audio signals, allowing seamless integration with modern multimedia devices such as Blu-ray players, gaming consoles, and streaming devices.

In addition to its robust audio capabilities, the Arcam AVR250 is also equipped with video processing technologies. It can upscale standard definition content to high-definition resolution, ensuring that older media looks sharper and more vibrant on modern displays. The receiver also features video switching capabilities, allowing users to connect multiple video sources and effortlessly switch between them.

User-friendliness is another hallmark of the AVR250, featuring an intuitive on-screen display and remote control that make setup and operation straightforward. The receiver also offers advanced room correction technologies, which utilize microphone measurements to optimize sound performance in various room acoustics. This ensures that audiences receive the best possible sound quality tailored to their specific environment.

In summary, the Arcam AVR250 exemplifies a blend of power, quality, and versatility. With its advanced audio technologies, comprehensive connectivity options, and user-friendly design, this home theater receiver is poised to elevate cinematic experiences and music reproduction in any home. Whether you are an audiophile or a casual viewer, the AVR250 caters to a wide array of listening preferences, making it a worthy addition to any audio setup.
Top Page Image Contents