Arcam AVR250 manual Using the Main Menu

Page 23

FM Mute/Mono

The AVR250’s tuner has an auto-muting circuit that, when engaged, mutes any signal that is of insufficient strength for listening. To engage this circuit press the FM MUTE/MONO button on the front panel: ‘FM MUTE’ is shown in the display. If a signal is muted you will hear no sound through the loudspeakers.

Should you wish to listen to a station that is ‘auto muted’ press the FM MUTE/MONO button again to disengage the muting circuit. The tuner now switches to monoaural reception, cancelling much of the background hiss. ‘FM MUTE’ is no longer displayed and you are able to continue listening.

Listening to the tuner in Zone 2

The tuner can be selected, as other inputs, for routing to Zone 2. Note, though, that it is not possible to listen to different stations in the main zone and Zone 2 simultaneously. This is because the AVR250 is fitted with just a single tuner module.

Using the Main Menu

Three ‘Main Menu’ screens allow day-to-day changes to be made to the way the AVR250 operates. Examples include adjusting the tone control for a particular input, or selection of ‘direct’ mode.

The three Main Menu screens are available on your display device. The selected line of each screen is also displayed on the front panel of the AVR250. Each of the following sections has a picture showing the screen that is displayed as you move through the menus.

Using the remote control to enter the Main Menu

Briefly press the MENU button to enter ‘Main Menu Screen 1’. Use the navigation5and6buttons to go up and down the menu respectively. The3and4buttons are used to alter the selection on the highlighted line, or to change to the next screen if the menu heading is highlighted.

Using the front panel to enter the Main Menu

Press the MENU button to enter the main menu. To cycle through the items on a menu, use the

EFFECT /6 button to go down and MODE/5button to go up one line for each press. Use the volume control knob for the3and4functions in order to cycle through the available choices, or to change the menu page if the menu heading is highlighted.

Main Menu Screen 1

Vol: Shows the present volume being used for the main zone and can be adjusted from here.

Audio Input: This shows the current audio input source selected. The current audio input can be changed when this line is highlighted using the source select buttons on the front panel or the remote. Note that changing the audio input also changes the video input to the same setting.

Video Input: This shows the current video input source selected. The current video input can be changed when this line is highlighted using the source select buttons on the front panel or the remote.

Changing the video input does not change the audio input, so you can watch a different input from the one you are listening to.

If the audio and video are set to different inputs, they will be reset to be the same input when the audio input is next changed.

Note: the composite/S-video inputs and the high-quality video inputs are independent of each other. If you are watching a video source by using the one of the high-quality video inputs, it is not possible to change the video input independently of the audio.

Video Type: This setting is applicable only to TVs being fed via a SCART lead where the trigger outputs fl and fm are connected via suitable SCART header. It shows the video aspect ratio currently selected for the display, which can be set manually to 4:3 or 16:9, depending on which format you are feeding into your TV. See page 12 for further details on using these triggers.

Stereo Direct:

nOFF: the AVR250 functions in its normal way.

nON: the AVR250 uses the analogue input signal for the source, bypassing the digital circuitry. In

this mode, the AVR250 functions like an analogue amplifier: it also shuts down all the unused digital circuitry for optimum stereo performance. Note that no digital output is available in this case.

Bass and Treble: These allow you to alter temporarily the bass and treble controls for all currently active speakers. In the case of Stereo, this would only apply to the front left and right speakers. In Effects, Pro Logic IIx Music, Dolby Digital and DTS modes (for example), this would apply to all present speakers.

You can adjust the bass and treble by up to ±6dB. These adjustments are in addition to those made in ‘Speaker Eq’ in the Set-up Menu. However, the maximum overall tone control range for each speaker using this screen plus the settings in ‘Speaker Eq’ is still ±6dB (not ±12dB).

Note that bass and treble alterations are not available in Stereo mode when AUTO STEREO TONE BYPASS is set to YES, or in Stereo Direct mode.

Balance: To alter temporarily the sound balance between the front left and right speakers. You can alter the sound stage to either the left or right by up to 10dB. Note that it is not possible to shift the audio signal completely over to one channel.

English

AVR250

E-23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents AVR250 Safety compliance Safety guidelinesImportant safety instructions Contents Introduction Using this handbookSafety Before you startBefore making connections Inserting the batteries into the remote controlCables InstallationPositioning the unit AVR250 rear panelConnection of record decks Audio connectionsAnalogue audio connections Subwoofer outputHigh quality Component video connections Scart RGB 4-WIRE ConnectionVideo connections Composite/S-video video connectionsZone 2 connections Connecting loudspeakersUsing bare wire ended leads Using spade terminalsConnecting to a power supply Connecting the AM and FM antennasNavigating the Set-up menu Configuring the AVR250Set-up mode Set-up Menu IndexSelect Cvbs status General Settings2/S-VIDEOtrigger is not active in this mode ‘Basic’ Set-up MenusSurr L/R Small Large Subwoofer SettingsSpeaker Sizes Distance measurements for 5.1 Speaker delay settings Speaker Delay SettingsUse Channels 6+7 for Level settingsEX Settings Test Tone CycleADV 1 Speaker Eq ADV 2 Video SettingsADV 3 Digital Settings ‘Advanced’ Set-up MenusSave Set-up Saving Settings and Exit Set-upADV 4 Zone 2 Settings ADV 5 Analogue SettingsRemote control Front panel display Switching on/offVolume control Operating your AVR250Zone HeadphonesInput selection Stereo DirectTreble/Bass Remote control buttonsEffects/FX ModeDeleting a preset Using the tunerTuning to a station Storing a presetUsing the Main Menu Effect Using ZoneDecoder splits the centre signal equally to IntroductionDigital multi-channel sources Surround modesMulti-channel source modes Two-channel source modesDSP Effects Modes Speaker positioningBi-amping your system Bi-wiring and bi-amping loudspeakersBi-wiring your loudspeakers Before you start important informationTroubleshooting Hum on an analogue input Source switching changes randomly or freezes on one sourceNo Zone 2 audio when playing DTS film Unable to adjust bass and treble controlsScart S-video cable with audio back to processor Scart connectionsScart RGB cable with audio back to processor IR Remote Codes Command Command codePreset/Tune down Preset/Tune up Preset/Tune mode toggle System code Command Command codePreset Power toggle MuteRadio interference Technical specificationsContinual improvement policy On line registration GuaranteeWorldwide Guarantee Appendix Serial programming interface Command and response formatsPower / Alimentation / Betriebsbereitschaft / Stroom Example / Exemple / Beispiel / Voorbeeld Mute / Coupure du son / Stumm / DempenDe audio- en video-ingang naar een zone wijzigen Changes the audio and video input to a zoneChange l’entrée audio et vidéo d’une zone Änderung des Audio- oder Videoeingangs einer ZoneDe video-ingang voor de hoofdzone wijzigen Changes the video input for the main zoneChange l’entrée vidéo de la zone principale Änderung der Videoquelle der HauptzoneDirect mode / Mode Direct / Direktmodus / Modus Direct Navigation / Navigation / Navigation / Navigatie Effect / Effet / Effekt / EffectStore / Mémorisation / Speichern / Opslaan Preset / Présélection / Voreinstellung / VoorinstellingRDS / Système RDS / RDS / RDS Tune / Réglage / Senderabstimmung / Afstemmen
Related manuals
Manual 44 pages 3.26 Kb Manual 44 pages 59.25 Kb

AVR250 specifications

The Arcam AVR250 is a distinguished model in the realm of home theater receivers, embodying high-performance audio and video processing capabilities that cater to discerning audiophiles and home cinema enthusiasts alike. Designed by Arcam, a company renowned for its commitment to delivering premium sound, the AVR250 stands out through its thoughtful engineering and robust feature set.

At the heart of the AVR250 lies a powerful amplification stage capable of delivering a peak output of 100 watts per channel into 8 ohms, ensuring that even the most demanding speakers can be driven with ease. This level of power translates into dynamic audio experiences, whether you're enjoying your favorite movies, music, or gaming. The receiver also incorporates a sophisticated digital signal processing engine that enhances sound quality and ensures accurate reproduction of all audio formats.

One of the standout features of the AVR250 is its support for multiple surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II. This enables users to experience surround sound in its full glory, bringing their favorite films to life with immersive audio tracks that add depth and realism to the viewing experience. The AVR250 also boasts an array of connectivity options, including HDMI inputs that support high-definition video and audio signals, allowing seamless integration with modern multimedia devices such as Blu-ray players, gaming consoles, and streaming devices.

In addition to its robust audio capabilities, the Arcam AVR250 is also equipped with video processing technologies. It can upscale standard definition content to high-definition resolution, ensuring that older media looks sharper and more vibrant on modern displays. The receiver also features video switching capabilities, allowing users to connect multiple video sources and effortlessly switch between them.

User-friendliness is another hallmark of the AVR250, featuring an intuitive on-screen display and remote control that make setup and operation straightforward. The receiver also offers advanced room correction technologies, which utilize microphone measurements to optimize sound performance in various room acoustics. This ensures that audiences receive the best possible sound quality tailored to their specific environment.

In summary, the Arcam AVR250 exemplifies a blend of power, quality, and versatility. With its advanced audio technologies, comprehensive connectivity options, and user-friendly design, this home theater receiver is poised to elevate cinematic experiences and music reproduction in any home. Whether you are an audiophile or a casual viewer, the AVR250 caters to a wide array of listening preferences, making it a worthy addition to any audio setup.
Top Page Image Contents