Hitachi 32HDT50, 50HDT50, 42HDT50 important safety instructions Power Source

Page 2

IMPORTANT

SAFETY POINTS YOU SHOULD KNOW ABOUT

YOUR HITACHI PLASMA TELEVISION

Our reputation has been built on the quality, performance, and ease of service of HITACHI Plasma Televisions.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI Plasma Television.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model.

Follow all warnings and instructions marked on this plasma television. Plasma television consists of AVC center and display monitor.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PLASMA TELEVISION TO RAIN OR MOISTURE.

NOTE: • There are no user serviceable parts inside the AVC center/display monitor.

• Model and serial numbers are indicated on back side of the AVC center/display monitor.

CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the user’s authority to operate the Plasma Television.

MODIFICATIONS: The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the user’s authority to operate the equipment.

POWER SOURCE

THIS PLASMA TELEVISION IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, AC CURRENT. INSERT THE AVC CENTER AND DISPLAY MONITOR POWER CORD INTO A 120 VOLT 60Hz OUTLET.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE PLASMA TELEVISION’S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE AVC CENTER/DISPLAY MONITOR TO 50Hz, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE.

NOTE: This Plasma Television will display television closed captioning, ( or ), in accordance with paragraph 15.119 of the FCC rules.

CAUTION: Never remove the back cover of the AVC center/display monitor as this can expose you to very high voltages and other hazards. If the television does not operate properly, unplug the Plasma Television and call your authorized dealer or service center.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Using the RGB Input Important Safety InstructionsRemote Control First Time USEPower Source Cart/apparatus combination to avoid injury Safety TipsOr table specified by the manufacturer, or Prevention of Screen BurnAccessories First Time USEHolder HOW to Setup Your NEW Hitachi Plasma TelevisionSpeaker Installation Ferrite CoreAntenna AVC Vertical Position Using AVC StandSecuring to a wall LocationHOW to SET UP Your NEW Hitachi Plasma Television ViewingHookup Cables Antenna Connections to Rear Jack PanelMENU/SELECT button Volume levelFront Panel Controls INPUT/EXIT buttonPhones Jack Audio OUT Rear Panel JacksMonitor OUT RGB Audio Input SUB-POWER buttonRGB Analog Input DVI Hdtv Digital InputConnecting Plasma Display Monitor to AVC BOX Connecting External Video SourcesBefore Operating External Video Source Connecting External Video SourcesConnecting a Monaural Audio Source to INPUT2~INPUT5 Connecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player Rear Panel of AVC CenterSee page 23 for tips on Rear Panel Connections DVD PlayerConnecting External AUDIO/VIDEO Devices Connecting External Audio AmplifierConnecting AV Network AV Network Setup Wizard Hitachi AV NET SET UPAUDIO/VIDEO Codes for AV Network not for remote control Rear Panel Connections Rear Panel of Display MonitorTips on Rear Panel Connections Remote Light ButtonSET-TOP-BOX STB HOW to USE the Remote to Control Your Plasma TVCable CBL Sleep button CD, PVR, AMP buttonsChannel selector buttons Info buttonAV NET button EquipmentSelect soft key to be learned HOW to USE the Remote To Control Your Plasma TVAV NET Learning Wizard Ratio Aspect buttonExpanded 480i/480p InputMenu button VOLUME, Mute buttonVideo button Exit buttonSurf button Last Channel Last CH buttonPICTURE-IN-PICTURE buttons 23 VID1 ~ VID5PIP button Split Mode PIPPICTURE-IN-PICTURE PIP PIP Mode button POP Mode PIPPIP Mode PIP Swap button with PIP onStrobe FREEZEwith PIP OFF Freeze button With PIP OFFSplit FREEZEwith PIP off POP Main Freeze with PIP OFFPrecoded VCR Buttons Using the Remote to Control VCR FunctionsOperating the precoded function for your VCR Exclusive TV ButtonsCable CBL button Using the Remote to Control Cable BOX FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttonsSET-TOP-BOX STB button Precoded SET-TOP-BOX/SATELLITE Receiver but- tonsPrecoded DVD Buttons Using the Remote to Control DVD FunctionsOperating the precoded function for your DVD player These buttons transmit the chosen precoded DVD codesUsing Your Remote To Control Additional Audio Equipment Operating the precoded function for your Audio componentAUDIO/VIDEO Codes for Remote Control only VCR BRAND. . . . . . . . . . . . . . . . . CodeOSD On-Screen Display Video Audio Aspect Chan Manager Locks Picture Mode VideoON-SCREEN Display Press down on Thumb Stick to select the function settingsUse the Thumb Stick Pure depending on the user’s preference Reset Video SettingsColor Management Auto Color Noise Reduction Auto Movie ModeColor Decoding Bass AudioTreble BalanceUse this function to select the Picture Format Aspect Ratio Aspect ModeAspect Auto AspectReception Band Channel ManagerChan. Manager 23 ~Auto Channel Scan Press Thumb Stick or Press Exit to quit the menu ScanChannel ID will not be displayed when PIP is on Channel IDLocks LocksMovie Ratings TV Ratings Canadian Ratings English Chart Canadian Ratings EngCanadian Ratings FrnMenu Preference SetupUse Thumb Stick or to select the sub-menu of your choice Menu Background SetupImage Power ScreenSet The Clock Set The ClockVideo Power Save Set The InputsBox Video 2 Auto LinkSet The Color System Set Event Timer Please Set Clock FirstWhen PIP Surf Mode is on, Closed Caption will not work Closed CaptionRGB on Screen Display Operation No SYNC. Signal Invalid Scan Freq TV/RGB Video Aspect Setup RGB on Screen Display This feature allows you to adjust brightness in RGB ModeColor Temperature BrightnessEnhancer ResetPreset condition AspectPosition Auto AdjustFor current RGB format are adjusted automatically Horizontal Clock Clock PhasePhase to factory preset, for current RGB format Black Side Panel Input LevelSelect the Input Level voltage between 0.7V Press down on Thumb Stick to select Black Side Panel ON/OFFCare of Your Hitachi Plasma Display Your Remote Control Do notUseful Info Ignition NoiseUseful Info Symptoms ControlPlug and Play Trademark AcknowledgmentAgency Regulatory Information Inputs OutputsHome Electronics Division Hitachi Way Chula Vista, CADigital Media Division Index QR55651
Top Page Image Contents