Hitachi 32HDT50 CD, PVR, AMP buttons, Channel selector buttons, Sleep button, Info button

Page 26

HOW TO USE THE REMOTE

TO CONTROL YOUR PLASMA TV

CD, PVR, AMP buttons

When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 39).

CHANNEL selector buttons

CHANNEL selector buttons are used to select channels, lock access code, etc.

Enter one, two, or three numbers to select channels. Enter “0” first for channels 1 to 9, or simply press the single digit channel you wish to tune then wait a few seconds for the TV to tune. For channels 100 and above, press the “1” button, wait until two dashes appear next to the channel display on your TV, then enter the remaining two numbers using the number buttons.

Channel selection may also be performed by pressing CH up ( ) or down ( ).

NOTE: The Plasma TV may not receive some channels if you are not in the correct ANTENNA/CABLE mode (see page 49).

SLEEP button

Press this button to display the sleep timer in the lower center of the screen. Every subsequent press of this button will add 15 min- utes to this timer, up to a maximum of three hours. Once set, use INFO when you want to view time remaining. If the SLEEP but- ton is pressed while the timer is set, it will reset to the original condition.

INFO button

Press this button when you want to check the channel being received, the picture source, if the channel has stereo (ST) or second audio program (SAP), the time, CHANNEL ID and if the SLEEP timer is set.

REMOTE CONTROL

Day/Night

Closed Mode

Captioning

3:32 PM

Time

Ant A 22

Main Picture Source

Stereo

Audio Broadcast

R

Broadcast Rating

1080i Format

Signal Format

Wide

Day

4:3 Expanded

Mode

CC Off

0:00 AM

-:--

Sleep Timer

View

Zzzz

3:32 PM S-IN:3

VID 3

3:32 PM YPBPR:1

VID 1

When an S-VIDEO Input is connected to VIDEO: 3.

When a COMPONENT VIDEO: Y-PBPRInput is connected to VIDEO: 1.

THE

Off Timer

ANTENNA button

The ANT button will select between Antenna A and Antenna B each time the button is pressed.

3:32 PM
Ant A 15	ANT
Stereo	ANT
G
G

TV/RGB button

Press this button to toggle between RGB (Analog) mode and TV mode.

3:32 PM

Ant B 22

Stereo

R

26

Image 26

Contents Using the RGB Input Important Safety InstructionsRemote Control First Time USEPower Source Cart/apparatus combination to avoid injury Safety TipsOr table specified by the manufacturer, or Prevention of Screen BurnAccessories First Time USEHolder HOW to Setup Your NEW Hitachi Plasma TelevisionSpeaker Installation Ferrite CoreAntenna AVC Vertical Position Using AVC StandSecuring to a wall LocationHOW to SET UP Your NEW Hitachi Plasma Television ViewingHookup Cables Antenna Connections to Rear Jack PanelMENU/SELECT button Volume levelFront Panel Controls INPUT/EXIT buttonPhones Jack Audio OUT Rear Panel JacksMonitor OUT RGB Audio Input SUB-POWER buttonRGB Analog Input DVI Hdtv Digital InputConnecting Plasma Display Monitor to AVC BOX Connecting External Video SourcesBefore Operating External Video Source Connecting External Video SourcesConnecting a Monaural Audio Source to INPUT2~INPUT5 Connecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player Rear Panel of AVC CenterSee page 23 for tips on Rear Panel Connections DVD PlayerConnecting External AUDIO/VIDEO Devices Connecting External Audio AmplifierConnecting AV Network AV Network Setup Wizard Hitachi AV NET SET UPAUDIO/VIDEO Codes for AV Network not for remote control Rear Panel Connections Rear Panel of Display MonitorTips on Rear Panel Connections Remote Light ButtonSET-TOP-BOX STB HOW to USE the Remote to Control Your Plasma TVCable CBL Sleep button CD, PVR, AMP buttonsChannel selector buttons Info buttonAV NET button EquipmentSelect soft key to be learned HOW to USE the Remote To Control Your Plasma TVAV NET Learning Wizard Ratio Aspect buttonExpanded 480i/480p InputMenu button VOLUME, Mute buttonVideo button Exit buttonSurf button Last Channel Last CH buttonPICTURE-IN-PICTURE buttons 23 VID1 ~ VID5PIP button Split Mode PIPPICTURE-IN-PICTURE PIP PIP Mode button POP Mode PIPPIP Mode PIP Swap button with PIP onStrobe FREEZEwith PIP OFF Freeze button With PIP OFFSplit FREEZEwith PIP off POP Main Freeze with PIP OFFPrecoded VCR Buttons Using the Remote to Control VCR FunctionsOperating the precoded function for your VCR Exclusive TV ButtonsCable CBL button Using the Remote to Control Cable BOX FunctionsOperating the precoded function for your cable box Precoded Cable BOX buttonsSET-TOP-BOX STB button Precoded SET-TOP-BOX/SATELLITE Receiver but- tonsPrecoded DVD Buttons Using the Remote to Control DVD FunctionsOperating the precoded function for your DVD player These buttons transmit the chosen precoded DVD codesUsing Your Remote To Control Additional Audio Equipment Operating the precoded function for your Audio componentAUDIO/VIDEO Codes for Remote Control only VCR BRAND. . . . . . . . . . . . . . . . . CodeOSD On-Screen Display Video Audio Aspect Chan Manager Locks Picture Mode VideoON-SCREEN Display Press down on Thumb Stick to select the function settingsUse the Thumb Stick Pure depending on the user’s preference Reset Video SettingsColor Management Auto Color Noise Reduction Auto Movie ModeColor Decoding Bass AudioTreble BalanceUse this function to select the Picture Format Aspect Ratio Aspect ModeAspect Auto AspectReception Band Channel ManagerChan. Manager 23 ~Auto Channel Scan Press Thumb Stick or Press Exit to quit the menu ScanChannel ID will not be displayed when PIP is on Channel IDLocks LocksMovie Ratings TV Ratings Canadian Ratings English Chart Canadian Ratings EngCanadian Ratings FrnMenu Preference SetupUse Thumb Stick or to select the sub-menu of your choice Menu Background SetupImage Power ScreenSet The Clock Set The ClockVideo Power Save Set The InputsBox Video 2 Auto LinkSet The Color System Set Event Timer Please Set Clock FirstWhen PIP Surf Mode is on, Closed Caption will not work Closed CaptionRGB on Screen Display Operation No SYNC. Signal Invalid Scan Freq TV/RGB Video Aspect Setup RGB on Screen Display This feature allows you to adjust brightness in RGB ModeColor Temperature BrightnessEnhancer ResetPreset condition AspectPosition Auto AdjustFor current RGB format are adjusted automatically Horizontal Clock Clock PhasePhase to factory preset, for current RGB format Black Side Panel Input LevelSelect the Input Level voltage between 0.7V Press down on Thumb Stick to select Black Side Panel ON/OFFCare of Your Hitachi Plasma Display Your Remote Control Do notUseful Info Ignition NoiseUseful Info Symptoms ControlPlug and Play Trademark AcknowledgmentAgency Regulatory Information Inputs OutputsHome Electronics Division Hitachi Way Chula Vista, CADigital Media Division Index QR55651