Hitachi 42HDT50 SET-TOP-BOX STB button, Precoded SET-TOP-BOX/SATELLITE Receiver but- tons

Page 37

USING THE REMOTE TO CONTROL

SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS

Operating the precoded function for your set-top-box/satellite receiver.

This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote command set of your set-top-box/satellite systems (refer to page 40).

1.Turn ON your set-top-box/satellite systems.

2.Aim the remote control at the front of your set-top-box/satellite systems.

3.Press and release the SET-TOP-BOX (STB) button to switch to set-top-box/satellite pre-coded mode.

4.Hold down the STB button on the remote and enter the two digit preset code that matches your set-top-box/satellite receiver as shown on page 40. The STB button light will flash 3 times if the code was accepted.

5.Aim the remote at the set-top-box/satellite receiver and press the POWER button. The remote will turn off your set-top-box/satel- lite receiver if the correct two digit preset code is entered. When this occurs, the remote control is programmed for your set-top- box/satellite receiver. If the set-top-box/satellite receiver does not turn off, try a different two digit preset code.

6.The remote will now control your set-top-box/satellite receiver.

NOTES:

1.If your set-top-box/satellite receiver cannot be operated after performing the above procedures, your set-top- box/satellite receiver code has not been precoded into the remote.

2.In the unlikely event that your set-top-box/satellite receiver cannot be operated after performing the above procedures, please consult your set-top-box/satellite receiver operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.The ANT button will act as the TV/STB button when in STB mode.

SET-TOP-BOX (STB) button

This button allows the remote to control your satellite receiv- er by setting it to SET-TOP-BOX/SATELLITE mode.

PRECODED SET-TOP-BOX/SATELLITE RECEIVER but- tons

These buttons transmit the chosen precoded set-top- box/satellite codes.

EXCLUSIVE TV buttons

These buttons are for operating the TV.

 

 

POWER

 

 

 

 

 

 

 

TV

VCR

 

 

CBL

 

 

STB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SOURCE WIZARD

 

 

 

 

DVD

CD

 

 

PVR

 

 

AMP

 

 

 

 

 

 

 

 

1

 

 

2

 

 

 

3

 

 

 

4

 

 

5

 

 

 

6

 

 

 

7

 

 

8

 

 

 

9

 

 

SLEEP

 

 

0

 

 

 

 

INFO

ANT

TV/RGB

A/V NET

 

ASPECT

VIDEO

 

 

 

 

 

 

 

 

 

 

MENU

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOL

 

SELECT

 

 

 

CH

 

 

 

 

 

 

 

 

 

 

 

 

 

MUTE

LAST

CH

 

 

 

 

VID1

 

 

 

 

 

 

 

VID

5

 

 

 

 

 

 

 

 

 

VID 2

 

VID 3

 

 

VID

4

 

 

 

 

 

 

 

 

 

 

 

 

 

PIP

 

 

SURF

 

 

 

FREEZE

 

 

 

 

 

PIP ACCESS

 

 

 

PIP MODE

 

 

SWAP

 

 

DAY/NIGHT

REC

THE REMOTE CONTROL

MY SATELLITE RECEIVER/STB CODE IS:

NOTE: Refer to instruction manual of the set-top-box/satellite receiver for operation of the buttons exclusively for the set-top- box/satellite receiver.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Remote Control Important Safety InstructionsUsing the RGB Input First Time USEPower Source Or table specified by the manufacturer, or Safety TipsCart/apparatus combination to avoid injury Prevention of Screen BurnFirst Time USE AccessoriesSpeaker Installation HOW to Setup Your NEW Hitachi Plasma TelevisionHolder Ferrite CoreSecuring to a wall AVC Vertical Position Using AVC StandAntenna LocationViewing HOW to SET UP Your NEW Hitachi Plasma TelevisionAntenna Connections to Rear Jack Panel Hookup CablesFront Panel Controls Volume levelMENU/SELECT button INPUT/EXIT buttonPhones Jack Monitor OUT Rear Panel JacksAudio OUT RGB Analog Input SUB-POWER buttonRGB Audio Input DVI Hdtv Digital InputConnecting External Video Sources Connecting Plasma Display Monitor to AVC BOXConnecting a Monaural Audio Source to INPUT2~INPUT5 Connecting External Video SourcesBefore Operating External Video Source Connecting a Stereo VCR or Stereo Laserdisc Player Rear Panel of AVC Center Connecting S-VIDEO VCR or Laserdisc PlayerDVD Player See page 23 for tips on Rear Panel ConnectionsConnecting External Audio Amplifier Connecting External AUDIO/VIDEO DevicesConnecting AV Network Hitachi AV NET SET UP AV Network Setup WizardAUDIO/VIDEO Codes for AV Network not for remote control Rear Panel of Display Monitor Rear Panel ConnectionsTips on Rear Panel Connections Light Button RemoteCable CBL HOW to USE the Remote to Control Your Plasma TVSET-TOP-BOX STB Channel selector buttons CD, PVR, AMP buttonsSleep button Info buttonEquipment AV NET buttonAV NET Learning Wizard HOW to USE the Remote To Control Your Plasma TVSelect soft key to be learned Expanded Aspect buttonRatio 480i/480p InputVideo button VOLUME, Mute buttonMenu button Exit buttonPICTURE-IN-PICTURE buttons Last Channel Last CH buttonSurf button 23 VID1 ~ VID5PICTURE-IN-PICTURE PIP Split Mode PIPPIP button PIP Mode PIP POP Mode PIPPIP Mode button Swap button with PIP onSplit FREEZEwith PIP off Freeze button With PIP OFFStrobe FREEZEwith PIP OFF POP Main Freeze with PIP OFFOperating the precoded function for your VCR Using the Remote to Control VCR FunctionsPrecoded VCR Buttons Exclusive TV ButtonsOperating the precoded function for your cable box Using the Remote to Control Cable BOX FunctionsCable CBL button Precoded Cable BOX buttonsPrecoded SET-TOP-BOX/SATELLITE Receiver but- tons SET-TOP-BOX STB buttonOperating the precoded function for your DVD player Using the Remote to Control DVD FunctionsPrecoded DVD Buttons These buttons transmit the chosen precoded DVD codesOperating the precoded function for your Audio component Using Your Remote To Control Additional Audio EquipmentVCR BRAND. . . . . . . . . . . . . . . . . Code AUDIO/VIDEO Codes for Remote Control onlyOSD On-Screen Display Video Audio Aspect Chan Manager Locks Video Picture ModeUse the Thumb Stick Press down on Thumb Stick to select the function settingsON-SCREEN Display Color Management Reset Video SettingsPure depending on the user’s preference Color Decoding Noise Reduction Auto Movie ModeAuto Color Treble AudioBass BalanceAspect Aspect ModeUse this function to select the Picture Format Aspect Ratio Auto AspectChan. Manager Channel ManagerReception Band 23 ~Auto Channel Scan Scan Press Thumb Stick or Press Exit to quit the menuChannel ID Channel ID will not be displayed when PIP is onLocks LocksMovie Ratings TV Ratings Canadian Ratings Eng Canadian Ratings English ChartFrn Canadian RatingsUse Thumb Stick or to select the sub-menu of your choice SetupMenu Preference Image Power SetupMenu Background ScreenSet The Clock Set The ClockSet The Inputs Video Power SaveSet The Color System Video 2 Auto LinkBox Please Set Clock First Set Event TimerClosed Caption When PIP Surf Mode is on, Closed Caption will not workRGB on Screen Display Operation No SYNC. Signal Invalid Scan Freq TV/RGB Video Aspect Setup Color Temperature This feature allows you to adjust brightness in RGB ModeRGB on Screen Display BrightnessPreset condition ResetEnhancer AspectFor current RGB format are adjusted automatically Auto AdjustPosition Phase to factory preset, for current RGB format Clock PhaseHorizontal Clock Select the Input Level voltage between 0.7V Input LevelBlack Side Panel Press down on Thumb Stick to select Black Side Panel ON/OFFDo not Care of Your Hitachi Plasma Display Your Remote ControlIgnition Noise Useful InfoControl Useful Info SymptomsTrademark Acknowledgment Plug and PlayAgency Regulatory Information Outputs InputsHitachi Way Chula Vista, CA Home Electronics DivisionDigital Media Division Index QR55651
Top Page Image Contents