Hitachi 32HLX61 HOW to USE the Remote To Control Additional Audio Equipment

Page 49

HOW TO USE THE REMOTE

TO CONTROL ADDITIONAL AUDIO EQUIPMENT

Operating the precoded function for your Audio component.

This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to pages 51-52 for pre-codes).

1.Turn ON your Audio component you wish to control with the Remote.

2.Aim the remote control at the front of your Audio component.

3. To switch to Audio (AMP) component pre-coded mode, use the SOURCE ACCESS buttons ( or ) on the remote control to position the LED light to the corresponding selection.

4.Hold down the ENT button on the remote and enter the four digit preset code that matches your Audio component, as shown on pages 51-52. Release the ENT button. The indicator light will flash 3 times if the code was accepted.

5.Aim the remote at the Audio component and press the POWER button. The remote will turn off your Audio component when the correct four digit preset code is entered. When this occurs, the remote control is programmed for your Audio component. If the Audio component does not turn off, try a different four digit preset code.

6.The remote will now control your Audio component.

7.Repeat steps 1 - 6 if you wish to program the remote to control another Audio component.

THE

NOTES:

1.If your Audio component cannot be operated after performing the above procedures, your Audio component’s code has not been precoded into the remote.

2.In the unlikely event that your Audio component cannot be operated after performing the above procedures, please consult your Audio equipment operating guide.

3.The remote control will remember the codes you have programmed until the batteries are removed from the remote control. After replacing the batteries repeat the entire programming procedure as stated above.

4.CD precode library is included in the AMP mode. Default device for this mode is Hitachi Audio/Video Receiver (AVR/AMP).

5.INPUT, GUIDE, Channel (up/down), Volume (up/down) and REC button are not for CD devices.

PRECODED AUDIO Buttons

These buttons transmit the chosen precoded Audio component codes.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

A/V NET

GUIDE

REMOTE CONTROL

MY AUDIO EQUIPMENT CODE IS:

CD

AMP/RCVR

NOTES: 1. The REC (Record) button only applies to some precoded amplifier/receiver codes.

2.Refer to instruction manual of the Audio equipment for operation of the buttons exclusively for the Audio equipment.

49

Image 49
Contents Operating Guide for 32HLX61 Do not Open Important Safety InstructionsPublic Viewing of Copyrighted Material Read before operating equipmentUSE AccessoriesTime FirstFirst Time USE HOW to Setup Your NEW Hitachi LCD TelevisionSecuring to a wall AntennaViewing HOW to SET UP Your NEW Hitachi LCD TelevisionBest Vertical Viewing AngleHookup Cables Antenna Connections to Rear Panel Jacks When both VHF and UHF antennas are connectedFirst Time VHF 75-Ohm antenna/CATV Cable TVPhoto Input Front Panel ControlsPhones Jack Monitor OUT Rear Panel JacksUpgrade Card SUB-POWER buttonTo Power Swivel Connector RGB Analog InputRear Panel of AVC CableCARD SlotConnecting LCD Display Monitor to AVC BOX Connecting External Video Sources Before Operating External Video Source Connecting a Monaural Audio Source to INPUT1~INPUT5Connecting a Stereo VCR or Stereo Laserdisc Player Connecting S-VIDEO VCR or Laserdisc Player Hdmi input VideoDVI to Hdmi Input See page 28 for tips on Rear Panel Connections Digital VCR D-VHS Connecting External Audio Amplifier Connecting External AUDIO/VIDEO DevicesConnecting AV Network Setup Procedure Using AV Network Device Codes AV Network Setup WizardCursor Pads To set the Input to whichTo set the Internal Speakers to Cursor PADOFF or TV as Center On the connectionsAUDIO/VIDEO Codes for AV Network not for remote control Time USE Rear Panel ConnectionsTips on Rear Panel Connections Remote Control Remote ControlHOW to USE the Remote To Control Your LCD TV Standard Aspect buttonExpanded PICTURE-IN-PICTURE button DAY/NIGHT buttonMenu button Guide buttonAV NET button ControlSelect the preferred TV Softkeys Ex AV NET Learning WizardPress the Select button Press Exit to QuitRemote Ant a Photo Input Ant BInput IeeeJump Rotate SlideshowWhen an IEEE1394 device is connected Info button When an S-VIDEOAnalog Channels Digital ChannelsChannel CH WHEEL/CHANNEL Selector buttons Volume VOL WHEEL, Mute buttonDash button Last Channel LC buttonPress the Cursor PAD or to enable the sub-picture sound POP Mode PICTURE-IN-PICTUREPICTURE-IN-PICTURE PIP PIP buttonSplit Mode PICTURE-IN-PICTURE PIP Mode PICTURE-IN-PICTURESurf Mode PICTURE-IN-PICTURE NtscSplit Freeze Main FreezeStrobe Freeze Operating the precoded function for your cable box HOW to USE the Remote To Control Cable BOX FunctionsPrecoded Cable BOX buttons Exclusive TV buttonsPRE-CODED SET-TOP-BOX/SATELLITE Receiver buttons Operating the precoded function for your DVD player HOW to USE the Remote To Control DVD FunctionsPrecoded DVD Buttons These buttons transmit the chosen precoded DVD codesPrecoded VCR/PVR Buttons HOW to USE the Remote To Control VCR/PVR FunctionsThese buttons transmit the chosen precoded VCR/PVR codes Operating the precoded function for your Audio component HOW to USE the Remote To Control Additional Audio EquipmentPrecoded Audio Buttons Input Access VCR Brand Audio Brand Simple Remote ON-SCREEN Display OSD On-Screen DisplayFor VideoChannel Manager Locks Timers Setup Power Swivel Video Picture ModeBack Light ContrastVideo Reset Video SettingsColor Decoding Noise Reduction Auto Movie ModeNatural ANT A/B, Video 480p/720p/1080iAudio Audio Language Digital OutputAspect AspectAuto Aspect Vertical PositionSet The Antenna Channel ManagerAuto Channel Scan Press Cursor PAD To highlight Ant a or Ant BChannel List Signal MeterLocks Movie Ratings TV Ratings Eng Canadian RatingsCanadian Ratings English Table Canadian Ratings French Table FrnProgramming is not suitable for children Programming restricted to adults ContainsSet The Clock TimersSet Day/Night Timer Set Sleep TimerPlease Set Clock First Set Event TimerSet Timer Recording Display SetupMenu Preference Menu Background Image PowerScreen SaverSet The Inputs Video 2 Auto Link ON-SCREENSet Black Side Panel Caption Mode Auto will turn Display on when Mute/Soft Mute is onSet Closed Caption Caption Display On/Off will turn the display on or offSet Monitor Out This feature will select the source of the Monitor OutputCableCARD Info Set AV ControlSet Stand-By Mode UpgradesPower Swivel Vesa RGB on Screen DisplayVGA Using the RGB Input No SYNC. Signal Invalid Scan Freq Shows which Remote This part of the screenRGB Input UsingColor Temperature This feature allows you to adjust brightness in RGB ModeContrast BrightnessEnhancer ResetBack Light AspectPosition UsingAdjusts the phase to correct blurred or unstable images Clock PhaseHorizontal Clock Power Swivel Using the RGBInput Level Black SideDo not Care of Your Hitachi LCD Display Your Remote ControlIgnition Noise Reception ProblemsGhosts SnowUseful Info SymptomsPicture Image Spectrum Important NotesTrademark Acknowledgment Plug and PlayAgency Regulatory Information Outputs InputsRGB, Video Hitachi Way Chula Vista, CA Home Electronics DivisionDigital Media Division Index Accessories23-26 Or the Software END User License Agreement for Hitachi DTV Software103 QR64521