Magnavox 32MF339B 5Initial Setup, Before you begin, After an initial setup is completed

PREPARATION

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure if the unit is connected to antenna or cables.

1After making all the necessary connections, press [y (power)] to turn on the unit.

• This operation may take a few moments.

2Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI iti l Setupt

Select the language for setup display.
			English
Elija el idioma de ajuste.
			Español
Sélectionner langue écran config.			Français
Select	OK OK	MENU
			Skip

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [OK].

3Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [OK].

InitialI iti l Setupt

Make sure the antenna is connected to ''ANT. IN'' jack.			Antenna
Select your signal source.
			Cable
			Skip
Antenna
Cable		Or	ANT.IN
Select	OK OK	BACK	MENU
		Back	Skip

• “Autoprogram” will begin.

InitialI iti l Setupt

Now the system is scanning for channels, please wait.

Auto programming will take up to 20 minutes to complete.

0%

Analog channels	0ch
Digital channels	0ch

MENU

Skip

4Use [Cursor s/ B] to select the desired location setting, then press [OK].

InitialI iti l Setupt

Select “Retail” or “Home” for your location.

Retail	H o m e
Select	OK OK

•Select ”Retail”, the unit will be set up with predefined setting for retail displays. In this setting, the power consumption may possibly exceed the limited requirement of the ENERGY STAR® qualification.

•Select ”Home”, the unit is set to maximize the energy efficiency for home setting and it can be adjusted through a choice of picture and sound quality according to your preference.

•When the initial setup is completed, the lowest memorized channel with the confirmation message of the location setting will be displayed on the TV screen.

Note:

•If you connect the cable system directly, contact the CATV installer.

•If you press [y (power)] or [MENU] during autoprogram, this setting will be canceled.

•The initial autoprogram function can be executed for either “Antenna” or “Cable” only once. When you change the connection (Antenna / Cable), set autoprogram again. (Refer to page 19.)

•If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

InitialI iti l Setupt

No channel is registered.	Retry
Try Autoprogram again?	Later
Verify that you have a cable connected to the "ANT. IN" jack on the
back of the TV, the channel installation process searches this
connection. If you are using a cable or satellite box, please confirm
the input which you have connected the box and press "SOURCE"
key on the remote control to select the appropriate source input.

Select	OK OK	MENU
		Skip

•You must set ”Home” in step 4. Otherwise, the settings of picture and sound quality you adjusted will not be memorized after you turn off the unit.

After an initial setup is completed...

•If you want to scan the channels automatically again. Refer to “Autoprogram” on page 19.

•You can add the desired channels unmemorized by “Autoprogram”. Refer to “Add Channels” on page 20.

•If you want to change the other language from the one you chose. Refer to “Language Selection” on page 21.

•If you want to change the mode for location setting. Refer to “Location” on page 32.

14

EN