Emerson LD195EM8 2, LD195EM8 7 5Auto Channel Scan, 5Language Selection, English, Español Français

e.g.) digital TV mode

INITIAL SETTING

BACK LIGHT

You can set the desired brightness mode. (Refer to “Back Light Setting” on page 24.)

COLOR TEMP.

You can adjust color temperature.

(Refer to “Color Temperature” on page 24.)

DTVCC

In addition to the basic closed caption described on page 21, DTV has its own closed caption called

DTVCC.

(Refer to “DTV Closed Caption” on page 22.)

PC SETTING

You can adjust the position, stability and clarity of the PC screen.

This menu will appear only in PC mode, and can only be set when the unit detects the PC input signal. (Refer to “PC Settings” on page 28.)

5Auto Channel Scan

If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channel you deleted, you will need to perform auto channel scan.

Before you begin:

Make sure if the unit is connected to antenna or cables.

1Press [SETUP] to display the main menu.

2Use [Cursor K / L] to select “CHANNEL SETUP”, then press [ENTER].

e.g.) digital TV mode

	- TV SETUP	-
or	CHANNEL SETUP
	V-CHIP SETUP
	LANGUAGE	[ENGLISH]
	CAPTION	[OFF]
	BACK LIGHT	[BRIGHT]
	COLOR TEMP.	[NORMAL]
	DTVCC

• Scanning and memorizing of channels start automatically.

D25

AUTO PRESET CH(DTV)

•When the scanning and memorizing are completed, the lowest memorized channel will be displayed.

•When you selected “AUTO PRESET CH(TV/DTV)”, the lowest memorized analog channel will be displayed when the scanning and memorizing are completed. If there is no analog channel, the lowest memorized digital channel will be displayed.

Note:

•After setting “Auto Channel Scan”, using [CH. K / L] on the remote control skips unavailable programs automatically.

•If you connect the cable system directly, contact the CATV installer.

•If you press [POWER] or [SETUP] during auto channel scan, the setting will be canceled.

•When no channel can be received by auto channel scan, “NO TV SIGNALS” will be displayed on the TV screen.

•Channel settings will be saved even if the power fails.

•If you have Spanish or French menus and need English, press [SETUP]. Use [Cursor K / L] to select “IDIOMA” or “LANGAGE”. Press [ENTER] repeatedly to select “ENGLISH”. Press [SETUP] to exit the main menu.

•With regard only to the digital channel, even after the scanning is completed if you unplug the AC power cord before turning off the unit by pressing [POWER], the channel setting may be lost.

5Language Selection

You can choose English, Spanish or French as your on-screen language.

1Press [SETUP] to display the main menu.

3Use [Cursor K / L] to select your desired preset type, then press [ENTER].

	e.g.) digital TV mode
	- CHANNEL SETUP -
or	ADD/DELETE(DTV)
	AUTO PRESET CH(DTV)
	AUTO PRESET CH(TV/DTV)
	AUTO PRESET CH(CATV)
	! CATV takes approx. 50min.

2Use [Cursor K / L] to select “LANGUAGE”,

then press [ENTER] repeatedly to change the setting.

e.g.) digital TV mode

	- TV SETUP	-
	CHANNEL SETUP
	V-CHIP SETUP
	LANGUAGE	[ENGLISH]
	CAPTION	[OFF]
	BACK LIGHT	[BRIGHT]
or	COLOR TEMP.	[NORMAL]
	DTVCC

ENGLISH

•When aerial antenna is connected,

select “AUTO PRESET CH(TV)”, “AUTO PRESET CH(DTV)” or “AUTO PRESET CH(TV/DTV)”.

•When connected to CATV, select “AUTO PRESET CH (CATV)”.

ESPAÑOL

FRANÇAIS

3Press [SETUP] to exit.

14

EN