Vidikron vision70 manual On / OFF, Source Selection Buttons Comp 1 SD Component, VID S-Video

Page 22

Controls and Functions

1.ON / OFF

Use these buttons to turn the projector on or off.

2.Source Selection Buttons:

COMP 1 (SD Component)

Press to select Component 1 (SD 480i/576i) video input as the source.

S-VID (S-Video)

Press to select the S-Video input as the source.

VIDEO

Press to select Composite video input as the source.

COMP 2 (HD Component)

Press to select Component 2 (HD 480p/576p/720p/1080i) video input as the source.

RGB HD

Press to select the Component 2 RGB input.

HDMI

Press to select the HDMI input.

3.Aspect Ratio Selection Buttons

Use these buttons to select an aspect ratio directly, as follows:

ANA (Anamorphic)

For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.

4X3 (Standard 4:3)

Scales the input signal to fit 4:3 display mode in the center of the screen.

L-BOX (Letterbox)

For viewing LaserDisc movies or non-anamorphic DVDs on a 4:3 screen.

I-WIDE (IntelliWide)

Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.

CINEMA

For viewing 2.35:1 source material.

C-FILL (CineWide-equipped projectors only)

Selects the Cinema Fill aspect ratio, used for viewing 16:9 source material on a 2.35:1 screen.

10	Vidikron Vision 70 Series Owner’s Operating Manual

Image 22

Contents

Series 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationMaintenance and Troubleshooting Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 70 at a Glance Temp LED Vision 70 Connector Panel Cable Access Door Open to access connectorsBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlVID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD ComponentPicture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens ControlsRemote Control 3InstallationOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 70/CineWide or Vision 70/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsProjector Model Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio VisionVertical and Horizontal Ceiling InstallationFloor Installation PositionFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 70 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 70/CineWide Vision 70/CineWide with Lens Base PlateFloor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting InvertedConnecting Source Connector Panel AccessConnections to the Vision 10. RGB Connections 11. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 12. Composite, S-Video and Component Video ConnectionsConnection 13. RS-232 Control System ConnectionEquipment AutoScope Lens Motor RearConnecting to AC Power Turning on the PowerPower source Focus Zoom Vertical Lens Shift Anamorphic Lens Installation Adjustment Vision 70/CineWide Installing and Adjusting the CineWide Anamorphic LensPrimary lens is perfectly centered on the screen Adjusting the Lens Height Y Anamorphic Lens Top View Vision 70/CineWide with AdjustmentAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Service AdjustInstallation PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Correct Vision 70 input Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 70 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsSpecifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 70 Dimensions Vision 70 Dimensions with Optional Fixed Anamorphic LensVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron