Vidikron vision70 manual Exit to return to the previous menu or Menu to exit, Installation

Page 67

Operation

Lamp Hours: Lamp Hours indicates how long the currently-installed lamp has been in service. (This part of the menu is read-only.)

To access the Installation adjustments, press MENU, then press the or button to highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. Press EXIT to return to the previous menu or press MENU to close all menus.

When you change a setting in the Installation menu, the change takes

Note effect immediately; you do not need to press ENTER afterwards. (Press

EXIT to return to the previous menu or MENU to exit.)

Language: Press the or button to select from the available languages (English, French, Spanish, German and Italian).

Picture Configuration: Press the or button to change the orientation of the projected image. The Vision 70 can be installed on a ceiling or in a rear-screen configuration with one or more mirrors. There are four settings: Floor Front, Ceiling Front, Floor Rear and Ceiling Rear.

Keystone: To correct distortion resulting from the angle of projection, select Keystone and use the or button to make the image rectangular.

Vidikron recommends that the keystone feature not be used unless

Tip

absolutely necessary, as it may cause artifacts in the image.

 

OSD Position: To adjust the horizontal and vertical position of the OSD, select OSD Position and press ENTER. Then, press the or button to select Horizontal or Vertical and use the or button to adjust.

OSD Timer: Use the or button to set the OSD Timer. This timer controls how long the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in 3-second increments. When you set the OSD Timer to 0, the menus remain on-screen until you hide them by pressing MENU.

PIP/PBP Setup: Select PIP/PBP Setup from the Installation menu to change the PIP/PBP settings.

•PIP/PBP Enable: Press the or button to select PIP/PBP Enable, then press ENTER. Press the or button to select Off or On, then press ENTER.

•PIP Set Up: Press the or button to select PIP Set Up, then press ENTER. Press the or button to select PIP Off, Graphic in Video or Video in Graphic, then press ENTER.

•PBP Set Up: Press the or button arrows to select PBP Set Up, then press ENTER. Press the or button to select PBP Off, Graphic by Video or Video by Graphic, then press ENTER.

Background Color: Press the or button to select the image Background Color (grey, blue or white). The Background Color appears when no incoming signal is present.

Installation

Installation

Language

Picture Configuration

Keystone

OSD Position

OSD Timer

PIP/PBP Setup

Background Color

Vidikron Vision 70 Series Owner’s Operating Manual

55

Page 66 Page 68
Image 67
Page 66 Page 68
Contents Series 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Table of ContentsMaintenance and Troubleshooting Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 70 at a Glance POWER/STANDBY LED Indicates power status as followsTemp LED Cable Access Door Open to access connectors Vision 70 Connector PanelBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlComp 2 HD Component On / OFFSource Selection Buttons Comp 1 SD Component VID S-VideoVAC V2 Aperture Control Memory Preset ButtonsCursor Keys Picture-In-Picture PIP / Picture-By-Picture PBP ControlsMotorized Lens Controls Remote Control/Built-In Keypad Functional ComparisonRemote Control 3InstallationOperation If installing a Vision 70/CineWide or Vision 70/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio Projector ModelPosition Ceiling InstallationFloor Installation Vertical and HorizontalFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 70 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Vision 70/CineWide with Lens Base Plate Installing the Fixed CineWide Base Plate Vision 70/CineWideCeiling Mounting Inverted Adjusting the ProjectorMounting the Vision Floor Mounting UprightConnecting Source Connector Panel AccessConnections to the Vision 10. RGB Connections DTV or Progressive Component YPbPr Source 11. Progressive Component Video Connections12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc13. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear EquipmentConnecting to AC Power Turning on the PowerPower source Focus Zoom Vertical Lens Shift Anamorphic Lens Installation Adjustment Vision 70/CineWide Installing and Adjusting the CineWide Anamorphic LensPrimary lens is perfectly centered on the screen Adjusting the Lens Height Y Anamorphic Lens Top View Vision 70/CineWide with AdjustmentAutoScope 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting Video MemoryUsing the On-Screen Menus Picture AdjustInstallation ServiceMain Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Correct Vision 70 input Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Commands Vision 70 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsSpecifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 70 Dimensions with Optional Fixed Anamorphic Lens Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron

vision70 specifications

The Vidikron Vision70 is a high-end home theater projector that has garnered attention for its exceptional performance and innovative technology. Tailored for cinephiles and enthusiasts seeking a premium viewing experience, the Vision70 combines advanced engineering with user-friendly features.

At the heart of the Vidikron Vision70 is its DLP (Digital Light Processing) technology. This approach utilizes a digital micromirror device to reflect light and create images, resulting in deep blacks, vibrant colors, and high contrast ratios. With a resolution of 1080p, the Vision70 delivers crisp imagery that captures even the finest details in your favorite films.

One of the standout features of the Vision70 is its remarkable brightness level, often reaching up to 2000 ANSI lumens. This ensures that the projector can perform well in varied lighting conditions, making it suitable for both dedicated home theaters and multipurpose media rooms. The lamp life, estimated to last around 3000 hours in eco mode, provides longevity and reliable performance for extended viewing sessions.

The Vision70 also boasts a wide color gamut, supporting multiple color spaces including standard REC 709 and cinema-grade DCI-P3. This enhancement translates to lifelike colors that resonate with the viewer, bringing content to life with remarkable accuracy. Additionally, the projector's dynamic iris technology further optimizes the contrast by adjusting light output in real-time according to scene demands.

For connectivity, the Vidikron Vision70 is equipped with multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices effortlessly. This ensures versatile use and that viewers can enjoy different content sources without hassle.

User convenience is a priority with the Vision70; the included remote control offers a seamless way to navigate through settings and features. Additionally, its compact design allows for relatively easy installation and setup in various environments.

In conclusion, the Vidikron Vision70 stands out in the crowded projector market with its combination of advanced DLP technology, impressive brightness, and exceptional color fidelity. Whether for movie nights, gaming, or sports viewing, the Vision70 promises an immersive and high-quality experience that caters to the needs of discerning audiences.
Top Page Image Contents