Vidikron vision70 manual Table of Contents, Operation

Page 8

Table of Contents

Mounting the Vision 70

24

Floor Mounting (Upright)

24

Ceiling Mounting (Inverted)

24

Adjusting the Projector Height or Projection Angle

24

Connections to the Vision 70

25

Connector Panel Access

25

Connecting Source Components to the Vision 70

25

RS-232 Controller Connection

29

Connecting 12-volt Trigger Output to External Theater Equipment

30

Connecting to AC Power

31

Turning on the Power

31

Changing the OSD Language

32

Adjusting the Picture Orientation

32

Primary Lens Adjustments

32

Focus

32

Zoom

32

Vertical Lens Shift

32

Installing and Adjusting the CineWide Anamorphic Lens

33

Anamorphic Lens Installation and Adjustment - Vision 70/CineWide

33

Anamorphic Lens Installation and Adjustment -

 

Vision 70/CineWide with AutoScope

36

4. Operation

43

Selecting Video Memory

43

Selecting an Aspect Ratio

43

Selecting An Input Source

43

Using Picture-In-Picture/Picture-By-Picture (PIP/PBP)

43

Using the On-Screen Menus

44

Main Menu

46

Picture Adjust

46

Image Option

51

Projector Status

54

Installation

55

Service

56

ISF Calibration

60

viii

Vidikron Vision 70 Series Owner’s Operating Manual

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Series 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationMaintenance and Troubleshooting Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualUsing This Manual They also provide supplemental informationPerformance or cause a malfunction If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 70 at a GlanceTemp LED Vision 70 Connector Panel Cable Access Door Open to access connectorsBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlOn / OFF Source Selection Buttons Comp 1 SD ComponentVID S-Video Comp 2 HD ComponentMemory Preset Buttons Cursor KeysPicture-In-Picture PIP / Picture-By-Picture PBP Controls VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens ControlsOperation 3InstallationRemote Control Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 70/CineWide or Vision 70/CineWideInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsThrow Ratios for the Vision 70 Series Throw Range Throw RatioProjector Model VisionCeiling Installation Floor InstallationVertical and Horizontal PositionFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 70 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 70/CineWide Vision 70/CineWide with Lens Base PlateAdjusting the Projector Mounting the VisionFloor Mounting Upright Ceiling Mounting InvertedConnections to the Vision Connector Panel AccessConnecting Source 10. RGB Connections 11. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 12. Composite, S-Video and Component Video ConnectionsConnection 13. RS-232 Control System ConnectionEquipment AutoScope Lens Motor RearPower source Turning on the PowerConnecting to AC Power Focus Zoom Vertical Lens Shift Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment Vision 70/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 70/CineWide with Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using Picture-In-Picture/ Picture-By-Picture PIP/PBP 4OperationSelecting Video Memory Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Adjust InstallationService PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Correct Vision 70 input Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 70 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsRegulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 70 Dimensions Vision 70 Dimensions with Optional Fixed Anamorphic LensVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron

vision70 specifications

The Vidikron Vision70 is a high-end home theater projector that has garnered attention for its exceptional performance and innovative technology. Tailored for cinephiles and enthusiasts seeking a premium viewing experience, the Vision70 combines advanced engineering with user-friendly features.

At the heart of the Vidikron Vision70 is its DLP (Digital Light Processing) technology. This approach utilizes a digital micromirror device to reflect light and create images, resulting in deep blacks, vibrant colors, and high contrast ratios. With a resolution of 1080p, the Vision70 delivers crisp imagery that captures even the finest details in your favorite films.

One of the standout features of the Vision70 is its remarkable brightness level, often reaching up to 2000 ANSI lumens. This ensures that the projector can perform well in varied lighting conditions, making it suitable for both dedicated home theaters and multipurpose media rooms. The lamp life, estimated to last around 3000 hours in eco mode, provides longevity and reliable performance for extended viewing sessions.

The Vision70 also boasts a wide color gamut, supporting multiple color spaces including standard REC 709 and cinema-grade DCI-P3. This enhancement translates to lifelike colors that resonate with the viewer, bringing content to life with remarkable accuracy. Additionally, the projector's dynamic iris technology further optimizes the contrast by adjusting light output in real-time according to scene demands.

For connectivity, the Vidikron Vision70 is equipped with multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices effortlessly. This ensures versatile use and that viewers can enjoy different content sources without hassle.

User convenience is a priority with the Vision70; the included remote control offers a seamless way to navigate through settings and features. Additionally, its compact design allows for relatively easy installation and setup in various environments.

In conclusion, the Vidikron Vision70 stands out in the crowded projector market with its combination of advanced DLP technology, impressive brightness, and exceptional color fidelity. Whether for movie nights, gaming, or sports viewing, the Vision70 promises an immersive and high-quality experience that caters to the needs of discerning audiences.
Top Page Image Contents