Vidikron vision70 manual Installing the Fixed CineWide Base Plate Vision 70/CineWide

Page 35

Installation

To install the fixed CineWide base plate on a Vision 70/CineWide:

1.Place the projector upside down on a blanket or other soft surface.

2.Line up the four mounting holes on the CineWide base plate with those on the bottom of the projector.

3.If you are mounting the Vision 70/CineWide on a ceiling: Line up the four holes on the projector ceiling mounting plate (included with the projector ceiling mount kit) with those on the bottom of the projector.

Note	The hole pattern on the CineWide base plate is identical to that on the
	ceiling mounting plate.

4.Secure the CineWide base plate (and ceiling mounting plate, if needed) to the projector with the four, M6x16mm screws and washers provided with the CineWide lens base plate. See Figure 3-8.

1. Do not use the mounting screws provided with the ceiling mounting Caution plate. Use only the hardware provided with the CineWide lens base

plate.

2.DO NOT OVER-TIGHTEN THE SCREWS.

Vision 70/CineWide with Lens Base Plate	Vision 70/CineWide with Lens Base Plate and
	Ceiling Mounting Plate

Figure 3-8. Vision 70/CineWide with Anamorphic Lens Base Plate and Ceiling Mounting Plate - Bottom View

Installing the Fixed CineWide Base Plate (Vision 70/CineWide)

Vidikron Vision 70 Series Owner’s Operating Manual

23

Image 35

Contents

Series 1080p DLP Projectors Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Table of ContentsMaintenance and Troubleshooting Table of Contents 1List of Figures List of Figures Xii About This Manual 1IntroductionIf you need Turn to Using This ManualThey also provide supplemental information Performance or cause a malfunctionDescription, Features and Benefits Optional Accessories Vision 70 at a Glance POWER/STANDBY LED Indicates power status as followsTemp LED Cable Access Door Open to access connectors Vision 70 Connector PanelBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlComp 2 HD Component On / OFFSource Selection Buttons Comp 1 SD Component VID S-VideoVAC V2 Aperture Control Memory Preset ButtonsCursor Keys Picture-In-Picture PIP / Picture-By-Picture PBP ControlsMotorized Lens Controls Remote Control/Built-In Keypad Functional ComparisonOperation 3InstallationRemote Control If installing a Vision 70/CineWide or Vision 70/CineWide Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeVision Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio Projector ModelPosition Ceiling InstallationFloor Installation Vertical and HorizontalFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 70 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Vision 70/CineWide with Lens Base Plate Installing the Fixed CineWide Base Plate Vision 70/CineWideCeiling Mounting Inverted Adjusting the ProjectorMounting the Vision Floor Mounting UprightConnections to the Vision Connector Panel AccessConnecting Source 10. RGB Connections DTV or Progressive Component YPbPr Source 11. Progressive Component Video Connections12. Composite, S-Video and Component Video Connections DTV Source DVD Player, VCR Satellite Receiver Etc13. RS-232 Control System Connection ConnectionAutoScope Lens Motor Rear EquipmentPower source Turning on the PowerConnecting to AC Power Focus Zoom Vertical Lens Shift Primary lens is perfectly centered on the screen Installing and Adjusting the CineWide Anamorphic LensAnamorphic Lens Installation Adjustment Vision 70/CineWide Adjusting the Lens Height Y Anamorphic Lens Top View AutoScope AdjustmentVision 70/CineWide with 18. Attaching the Anamorphic Lens to the Lens Adapter Ring Attach Lens Mounting Assembly to Lens Motor Carriage PlateAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting an Aspect Ratio Selecting An Input Source Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting Video MemoryUsing the On-Screen Menus Picture AdjustInstallation ServiceMain Menu Picture AdjustTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionDescription Aspect Ratio SettingsRemote Projector Status Exit to return to the previous menu or Menu to exit InstallationService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp assembly for replacement 5Maintenance and TroubleshootingLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Correct Vision 70 input Maintenance and Troubleshooting 6Serial Communications Serial Command SyntaxRS-232 Connection and Port Configuration Serial CommandsSerial Communications Serial Commands Serial Commands Vision 70 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsRegulatory Approvals Limited WarrantySpecifications are subject to change without notice Vision 70 Dimensions with Optional Fixed Anamorphic Lens Vision 70 DimensionsVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron