Vidikron vision70 manual Adjusting the Lens Height Y

Page 46

Installation

1.Use the Pitch/Y-Adjustment Screws and Washers (item #6) to attach the Vertical Mounting Brackets (item #5) to the Anamorphic Lens (item #1).

2.Place the lens with the brackets installed on top of (or under, if the projector is inverted) the Base Plate (item #2), so that the two threaded posts at the bottom of the brackets pass through the corresponding slots on the base plate.

3.Secure the lens assembly to the base plate with the Yaw/Z-Adjustment Levers and Fiber Washers (item #4).

To avoid clipping the corners of the image, position the anamorphic lens

Tip

as close as possible to the primary lens.

 

 

 

Ceiling Mount

 

 

Bracket

 

 

 

 

Adjusting the Lens Height (Y):

1.Project a white field on the screen.

2.Ensure that the two Pitch/Y-Adjustment Screws are loose enough to allow vertical movement of the lens assembly.

3.Slowly move the anamorphic lens into place so that there are no shadows on the top or bottom of the screen:

Too Low

Correct position

Too High

4.When the height is properly set, tighten the Pitch/Y-Adjustment Screws to secure the lens in place.

Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom pincushion distortion. To do this, loosen the Pitch/Y-Adjustment Screws on either side of the lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected image is rectangular:

34

Vidikron Vision 70 Series Owner’s Operating Manual

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Series 1080p DLP Projectors Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Table of Contents OperationMaintenance and Troubleshooting Table of Contents 1List of Figures List of Figures Xii 1Introduction About This ManualPerformance or cause a malfunction Using This ManualThey also provide supplemental information If you need Turn toDescription, Features and Benefits Optional Accessories POWER/STANDBY LED Indicates power status as follows Vision 70 at a GlanceTemp LED Vision 70 Connector Panel Cable Access Door Open to access connectorsBuilt-In Keypad Vision 70 Remote Control Vision 70 Remote ControlVID S-Video On / OFFSource Selection Buttons Comp 1 SD Component Comp 2 HD ComponentPicture-In-Picture PIP / Picture-By-Picture PBP Controls Memory Preset ButtonsCursor Keys VAC V2 Aperture ControlRemote Control/Built-In Keypad Functional Comparison Motorized Lens ControlsRemote Control 3InstallationOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 70/CineWide or Vision 70/CineWideInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsProjector Model Throw Ratios for the Vision 70 SeriesThrow Range Throw Ratio VisionVertical and Horizontal Ceiling InstallationFloor Installation PositionFolded Optics Installing the Optional CineWide Lens Mount With AutoScope Vision 70 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 70/CineWide Vision 70/CineWide with Lens Base PlateFloor Mounting Upright Adjusting the ProjectorMounting the Vision Ceiling Mounting InvertedConnecting Source Connector Panel AccessConnections to the Vision 10. RGB Connections 11. Progressive Component Video Connections DTV or Progressive Component YPbPr SourceDTV Source DVD Player, VCR Satellite Receiver Etc 12. Composite, S-Video and Component Video ConnectionsConnection 13. RS-232 Control System ConnectionEquipment AutoScope Lens Motor RearConnecting to AC Power Turning on the PowerPower source Focus Zoom Vertical Lens Shift Anamorphic Lens Installation Adjustment Vision 70/CineWide Installing and Adjusting the CineWide Anamorphic LensPrimary lens is perfectly centered on the screen Adjusting the Lens Height Y Anamorphic Lens Top View Vision 70/CineWide with AdjustmentAutoScope Attach Lens Mounting Assembly to Lens Motor Carriage Plate 18. Attaching the Anamorphic Lens to the Lens Adapter RingAdjusting the Horizontal X Lens Position Installation Anamorphic Lens Top View Adjusting the Geometry Installation Selecting Video Memory Using Picture-In-Picture/ Picture-By-Picture PIP/PBP4Operation Selecting an Aspect Ratio Selecting An Input SourceUsing the On-Screen Menus Service AdjustInstallation PicturePicture Adjust Main MenuPerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Image Option Image OptionAspect Ratio Settings DescriptionRemote Projector Status Installation Exit to return to the previous menu or Menu to exitService ServiceOperation Operation Remote Control ISF Calibration ISF CalibrationOperation Operation Lamp Replacement 5Maintenance and TroubleshootingLamp assembly for replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Correct Vision 70 input Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration 6Serial CommunicationsSerial Communications Serial Commands Serial Commands 7Specifications Vision 70 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsSpecifications are subject to change without notice Limited WarrantyRegulatory Approvals Vision 70 Dimensions Vision 70 Dimensions with Optional Fixed Anamorphic LensVidikron Vision 70 Series Owner’s Operating Manual Power-cycle the projector to see the change Page Vidikron

vision70 specifications

The Vidikron Vision70 is a high-end home theater projector that has garnered attention for its exceptional performance and innovative technology. Tailored for cinephiles and enthusiasts seeking a premium viewing experience, the Vision70 combines advanced engineering with user-friendly features.

At the heart of the Vidikron Vision70 is its DLP (Digital Light Processing) technology. This approach utilizes a digital micromirror device to reflect light and create images, resulting in deep blacks, vibrant colors, and high contrast ratios. With a resolution of 1080p, the Vision70 delivers crisp imagery that captures even the finest details in your favorite films.

One of the standout features of the Vision70 is its remarkable brightness level, often reaching up to 2000 ANSI lumens. This ensures that the projector can perform well in varied lighting conditions, making it suitable for both dedicated home theaters and multipurpose media rooms. The lamp life, estimated to last around 3000 hours in eco mode, provides longevity and reliable performance for extended viewing sessions.

The Vision70 also boasts a wide color gamut, supporting multiple color spaces including standard REC 709 and cinema-grade DCI-P3. This enhancement translates to lifelike colors that resonate with the viewer, bringing content to life with remarkable accuracy. Additionally, the projector's dynamic iris technology further optimizes the contrast by adjusting light output in real-time according to scene demands.

For connectivity, the Vidikron Vision70 is equipped with multiple HDMI inputs, allowing users to connect various devices like Blu-ray players, gaming consoles, and streaming devices effortlessly. This ensures versatile use and that viewers can enjoy different content sources without hassle.

User convenience is a priority with the Vision70; the included remote control offers a seamless way to navigate through settings and features. Additionally, its compact design allows for relatively easy installation and setup in various environments.

In conclusion, the Vidikron Vision70 stands out in the crowded projector market with its combination of advanced DLP technology, impressive brightness, and exceptional color fidelity. Whether for movie nights, gaming, or sports viewing, the Vision70 promises an immersive and high-quality experience that caters to the needs of discerning audiences.
Top Page Image Contents