Vidikron Vision 12, Vision 10 Vidikron Logo, Vertical Lens Shift Dial Shifts the image up or down

Page 16

Controls and Functions

1.TOP IR SENSOR

2.VERTICAL LENS SHIFT DIAL Shifts the image up or down.

3.INTAKE VENT

4.ADJUSTABLE FEET

Use to adjust the height or projection angle.

5.VIDIKRON LOGO

The logo can be rotated to match the projector orientation: inverted (ceiling-mounted) or upright. To rotate the logo, grip it at the sides, pull it away from the projector and rotate it 180 degrees.

6.FRONT IR SENSOR

7.FOCUS/ZOOM RING

8.EXHAUST VENT

9.HORIZONTAL LENS SHIFT DIAL

10.TEMPERATURE INDICATOR

Flashes blue when the projector is overheated.

11.POWER INDICATOR

Lights solid blue when the projector is in standby mode; flashes blue during cool-down. During normal operation, this LED is off.

6	Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Image 16

Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn to Description, Features and Benefits Key Features and BenefitsOptional Accessories Vision 10/12 at a Glance 2Controls and FunctionsFront/Top/Side View Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Example only Adjusting the Projection Vertical and Horizontal Lens Shift LimitsAngle VisionFolded Optics Connections to the Vision 10/12 Connector Panel AccessTo Source Components Hdmi or DVI Source Connections Analog RGB Connections Component Video Connections 10. Composite and S-Video Connections Connection 12. Connecting the 12-Volt Trigger Output Trigger OutputAdjusting the Projector Height or Projection Angle Turning on the Power4Operation Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Settings Source Select Main MenuAspect Ratio Aspect Ratio Settings Control DescriptionRGB-HD Hdmi Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Settings ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsPower Requirements DimensionsWeight including lens Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsComputer Signal Compatibility Computer Signal Compatibility ChartResolution Horizontal VerticalDisplay Video Signal Compatibility Video Signal Compatibility ChartFreq Compatible Inputs Note Resolution CompPage RUMA-011175