Vidikron Vision 12, Vision 10 manual Installation

Page 54

Operation

Source :

Component 1

Resolution:

720 x 480

Vert Freq :

60 Hz

Horz Freq :

31 kHz

Lamp Timer :

720 HR

F/W Version :

226.4.150

 

 

Information: Select Information from the Main Menu to see information about the current source, input resolution, horizontal and vertical frequencies, lamp hours and the installed firmware version.

Should you ever need to contact Vidikron Technical Support, this information will help them answer your questions or resolve product performance issues.

Restore Factory Settings: To reset all items in the Image Options menu to their factory default values, select Restore Factory Settings and press ENTER. A warning message appears; press ENTER again to confirm the reset or press EXIT to cancel. After the reset, the projector powers off and restarts.

Installation ➤

Installation

Language

English

Picture Configuration

Floor Front

OSD Timeout

5 secs

OSD Transparent

OFF

Source Detect

Auto

Auto Power Off

OFF

Blue Enable

OFF

OSD Position

 

Keystone

 

Fan High Speed Mode

ON

 

 

The Installation menu to change the picture orientation, appearance and behavior of the OSD menus, fan speed and other projector settings.

Language: Select Language from the Installation menu and press the right- or left-arrow buttons to select the OSD language (English, French, Italian, German or Spanish).

Picture Configuration: Select Picture Configuration from the Installation menu to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

OSD Timeout: The OSD Timeout setting controls how long the OSD menus stay on screen when no buttons are pressed. Select a time-out period of 5, 15 or 60 seconds.

OSD Transparent: To allow the projected image to show through the OSD menus, select OSD Transparent from the Installation menu and set it to ON.

Source Detect: The Vision 10/12 can automatically detect an incoming signal and switch to that input. To enable automatic source detection, select Source Detect from the Installation menu and set it to Auto.

Auto Power Off: The Vision 10/12 can be set to power off automatically after 15 minutes of no input signal or user input via the remote control. To enable this feature, set it to ON. When you do, a warning message appears on-screen five minutes before the shutdown is to occur. To prevent the projector from powering off, press any key on the remote control.

Blue Enable: Blue Enable removes all red and green color information from the image, simulating a blue filter. You can use it instead of a blue filter when performing color and tint adjustments.

OSD Position: To change the position of the OSD controls, select OSD Position from the Installation menu. Use the up- and down-arrow buttons to select Top Left, Bottom Left, Top Right or Bottom Right, then press ENTER.

44

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Page 53 Page 55
Image 54
Page 53 Page 55
Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories 2Controls and Functions Vision 10/12 at a GlanceFront/Top/Side View Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Example only Angle Adjusting the ProjectionVertical and Horizontal Lens Shift Limits VisionFolded Optics Connector Panel Access Connections to the Vision 10/12To Source Components Hdmi or DVI Source Connections Analog RGB Connections Component Video Connections 10. Composite and S-Video Connections Connection 12. Connecting the 12-Volt Trigger Output Trigger OutputTurning on the Power Adjusting the Projector Height or Projection Angle4Operation Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Settings Main Menu Source SelectAspect Ratio Aspect Ratio Settings Control DescriptionRGB-HD Hdmi Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Settings ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsWeight including lens Power RequirementsDimensions Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsResolution Computer Signal CompatibilityComputer Signal Compatibility Chart Horizontal VerticalDisplay Freq Compatible Inputs Note Resolution Video Signal CompatibilityVideo Signal Compatibility Chart CompPage RUMA-011175
Top Page Image Contents