Vidikron Vision 12, Vision 10 manual Image Option

Page 52

Operation

 

White Balance

R Gain

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

G Gain

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

B Gain

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

R Offset

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

G Offset

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

B Offset

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

Image Option

Image Option

HD/RGB Adjust

Image Position

Over Scan Adjust

 

1%

SDTV Adjust

 

 

Brightness Enhance

 

OFF

Lamp Power

 

250W

Information

 

 

Restore Factory Settings

 

 

 

 

ICC Select: Choose ICC Select from the Picture Adjust menu to specify the color space (Standard, NTSC, HDTV or PAL) that is appropriate for the source signal, to achieve optimal color balance.

If you select NTSC, HDTV or PAL, you can make further adjustments to individual color space characteristics in the ICC Adjust sub-menu under the ISF Settings menu, described later in this section. (The Standard color space is factory-set and not adjustable.)

White Balance: To remove any trace of color from the white areas of the projected image, choose White Balance from the Picture Adjust menu and press ENTER.

Gain: Use the Gain controls to correct color imbalances in the bright areas of the image. A good way to do this is to use a test pattern consisting mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red, green or blue, decrease the Gain for that color.

Offset: Use the Offset controls in the White Balance sub-menu to correct color imbalances in the dark areas of the image. A good way to do this is to use a test pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray areas contain traces of red, green or blue, decrease the Offset for that color.

Save Settings: The Vision 10/12 lets you save image quality settings for each input and supported resolution to a preset. You can recall this preset at a later time by simply pressing a button on the remote control or using the Load Saved Settings menu command (see below).

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

Aspect ratio

Picture adjustments (brightness, contrast, color saturation, tint, sharpness, gamma, color temperature, ICC selection and white balance settings)

Image options (SDTV adjust settings, brightness enhance, lamp power)

Load Saved Settings: To recall a preset, choose Load Saved Settings from the Picture Adjust menu and select “Custom1,” “ISF Day” or “ISF Night.” Or, use the corresponding buttons on the remote control.

Use the controls in the Image Option menu to perform advanced image quality adjustments, obtain information about the projector or perform a factory reset.

HD/RGB Adjust: To improve the quality of projected images from a computer or other analog RGB source, select HD/RGB Adjust and press ENTER.

Clock: If you notice flickering or vertical noise when displaying computer images, adjust the Clock setting to correct the issue.

Phase: Adjust the phase if the image shows shimmer or “horizontal” noise. Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

To restore the original Clock and Phase settings, select Reset and press ENTER, then press ENTER again to confirm the reset.

42

Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Image 52
Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Vision 10/12 at a Glance 2Controls and FunctionsFront/Top/Side View Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationInstallation Overview Quick SetupStep Procedure For Details, refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Example only Adjusting the Projection Vertical and Horizontal Lens Shift LimitsAngle VisionFolded Optics Connections to the Vision 10/12 Connector Panel AccessTo Source Components Hdmi or DVI Source Connections Analog RGB Connections Component Video Connections 10. Composite and S-Video Connections Connection 12. Connecting the 12-Volt Trigger Output Trigger OutputAdjusting the Projector Height or Projection Angle Turning on the Power4Operation Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Settings Source Select Main MenuAspect Ratio Aspect Ratio Settings Control DescriptionRGB-HD Hdmi Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Settings ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsPower Requirements DimensionsWeight including lens Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsComputer Signal Compatibility Computer Signal Compatibility ChartResolution Horizontal VerticalDisplay Video Signal Compatibility Video Signal Compatibility ChartFreq Compatible Inputs Note Resolution CompPage RUMA-011175