Vidikron Vision 12, Vision 10 manual Connecting the 12-Volt Trigger Output

Page 38

Installation

Connecting to the 12-Volt	➤	If your home theater contains a retractable screen or other, 12-Volt trigger-activated
Trigger Output		equipment, connect it to the 12-volt trigger output on the Vision 10/12 as shown in Figure
		3-12.

COMP 1

COMP 2

VIDEO

S-VIDEO

PR/CR

PB/CB

Y

PR/CR

PB/CB

Y

RGB-HD

HDMI

VIDEO

VIDEO-S

R

C/

R

P

B

B

P

Y

R

R

P

B

B

P

Y

HD-RGB

HDMI

C/

C/

C/

1 COMP

2 COMP

RS-232

232-RS

		Retractable Screen
	3.5-mm	or other, 12-volt
	3.5-mm	trigger-activated equipment
	mini plug	trigger-activated equipment
	mini plug

Black = Ground (Sleeve)

Red = +12V (Tip)

Figure 3-12. Connecting the 12-Volt Trigger Output

28	Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Image 38

Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Front/Top/Side View 2Controls and FunctionsVision 10/12 at a Glance Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationStep Procedure For Details, refer to Quick SetupInstallation Overview Installation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Example only Angle Adjusting the ProjectionVertical and Horizontal Lens Shift Limits VisionFolded Optics To Source Components Connector Panel AccessConnections to the Vision 10/12 Hdmi or DVI Source Connections Analog RGB Connections Component Video Connections 10. Composite and S-Video Connections Connection 12. Connecting the 12-Volt Trigger Output Trigger Output4Operation Turning on the PowerAdjusting the Projector Height or Projection Angle Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Settings Aspect Ratio Main MenuSource Select Aspect Ratio Settings Control DescriptionRGB-HD Hdmi Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Settings ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Symptom Possible Causes Solution Troubleshooting TipsTroubleshooting Chart Maintenance and Troubleshooting Serial Commands Serial Command SyntaxRS-232 Connection and Port Configuration Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsWeight including lens Power RequirementsDimensions Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsResolution Computer Signal CompatibilityComputer Signal Compatibility Chart Horizontal VerticalDisplay Freq Compatible Inputs Note Resolution Video Signal CompatibilityVideo Signal Compatibility Chart CompPage RUMA-011175