Vidikron Vision 12, Vision 10 manual Cleaning the Intake and Exhaust Vents

Page 60

Maintenance and Troubleshooting

5.3

Cleaning the Intake and Exhaust Vents

This Vision 10/12 is equipped with intake and exhaust vents to allow the flow of cool air through the projector and maintain the proper operating temperature.

You should periodically clean the vents by vacuuming them with a vacuum cleaner. Vidikron recommends doing this after every 100 hours of use, or more often if the projector is used in a dirty or smoky location.

To clean the intake and exhaust vents:

1.Press OFF on the remote control to turn off the power. Wait until the cooling fan stops.

2.Unplug the power cord.

3.Remove dust by placing the cleaner hose on the intake and exhaust vents.

Side and front view

Ventilation holes

Power OFF button

50	Vidikron Vision Model 10/Model 12 Owner’s Operating Manual

Image 60

Contents 10/12 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Safety Precautions 1Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial Communications1List of Figures List of Figures 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories 2Controls and Functions Vision 10/12 at a GlanceFront/Top/Side View Vidikron Logo Vertical Lens Shift Dial Shifts the image up or downRear/Top/Side View Vision 10/12 Rear/Top/Side ViewLamp Cover Exhaust Vent Vision 10/12 Remote Control Vision 10/12 Remote ControlISF DAY Light Controls and Functions 3Installation Remote ControlAvailable Range of the Remote Control OperationQuick Setup Installation OverviewStep Procedure For Details, refer to Installation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsEstimating Throw Distance TD Vertical and Horizontal Horizontal Lens Shift Example only Adjusting the Projection Vertical and Horizontal Lens Shift LimitsAngle VisionFolded Optics Connector Panel Access Connections to the Vision 10/12To Source Components Hdmi or DVI Source Connections Analog RGB Connections Component Video Connections 10. Composite and S-Video Connections Connection 12. Connecting the 12-Volt Trigger Output Trigger OutputTurning on the Power Adjusting the Projector Height or Projection Angle4Operation Changing the OSD Language Adjusting the Picture Orientation Lens Adjustments Focus/ZoomUsing the On-Screen Menus Cause the projector to malfunctionVision 10/12 OSD Menu Structure ISF Settings Main Menu Source SelectAspect Ratio Aspect Ratio Settings Control DescriptionRGB-HD Hdmi Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Effect of X and Y Coordinates for Color Temperature AdjustmentImage Option Auto Tune may take some time to complete, depending on Installation Horizontal Keystone Correction Vertical Keystone CorrectionISF Settings ISF Calibration11. ISF-Enabled Vision 10/12 Splash Screen Blue Enable Refer to Blue Enable on 5Maintenance and Troubleshooting Cleaning the Projector Cleaning the LensCleaning the Intake and Exhaust Vents Lamp Maintenance Lamp CautionsLamp Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationSerial Commands Command Description ReplySerial Communications 7Specifications Vision 10/12 SpecificationsPower Requirements DimensionsWeight including lens Home Theater Calibration SpecificationsVision 10/12 Dimensions 1shows the Vision 10/12 dimensionsComputer Signal Compatibility Computer Signal Compatibility ChartResolution Horizontal VerticalDisplay Video Signal Compatibility Video Signal Compatibility ChartFreq Compatible Inputs Note Resolution CompPage RUMA-011175