Vidikron Vision 120 operation manual Gray Yellow Cyan Green Magenta Red Blue

Page 70

Operation

Select Color and press ENTER or SELECT. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

gray

yellow

cyan

green

magenta

red

blue

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint and press ENTER or SELECT. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

Like the brightness and contrast controls, the color and tint controls are

Note interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

56	Vidikron Vision Model 120 Installation/Operation Manual

Image 70

Contents 120 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate OperationMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Vision 120 offers these key features and benefitsOptional Accessories Controls and Functions Vision 120 at a GlanceVision 120 Rear Panel Vision 120 Rear PanelUSB-B DVI-DL Dual-LinkVHD Controller Front Panel VHD Controller Front PanelIssue LED DVI-DL DUAL-LINK Output 1080p Service only For future useVHD Controller Rear Panel RS-232/485 Control PortHdmi I 1 / Hdmi II 2 Digital 10. HD3 InputVision 120 Remote Control Vision 120 Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox LetterboxRemote Control 3InstallationOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 120/CineWide or VisionInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsVision 120 Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vision 120 Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Floor Mounting Upright Ceiling Mounting Inverted Adjusting the ProjectionMounting the Vision AngleConnecting the VHD Connector Panel AccessConnections to the Vision 120 and VHD Controller Hdmi Connections See Figure Connecting SourceController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 16. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentVHD Controller Connecting an External IR Receiver to the VHD ControllerRear Panel Adjusting the Picture Orientation Turning on the PowerPower source Focus Primary Lens AdjustmentsZoom Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using the On-Screen Menus 4OperationInput Source Memory PresetsService Aspect RatioInput Source Main MenuAspect Ratio 169 Aspect Ratio SettingsDescription Hdtv programs in their nativePicture PicturePerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationCalibration ISF Night CalibrationISF Day OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, aboveService ServiceHD Format Presets 5Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command Syntax6Serial Communications Input Selection Commands Serial Commands and ResponsesCommand Description Response Aspect Ratio CommandsPicture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonSerial Communications 7Specifications Vision 120 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 120 Dimensions Vision 120/CineWide with AutoScope DimensionsSupported Signal Timings by Input Supported TimingsFormat Resolution Frequency HD 1/HD 2/HD Page Vidikron