Vidikron Vision 120 operation manual Presets

Page 76

Operation

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

If your projector is equipped with the Vidikron CineWide with AutoScope system, assign at least one trigger output (the same one to which the lens motor is connected) to the Cinema and IntelliWide 2.35 aspect ratios.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD Language (English, Français, Deutsch, Español or Italiano).

•OSD Timer: Select OSD Timer from the Miscellaneous menu to set the OSD Timer, which controls how long the menus remain on-screen after selecting them. Select from 5 to 60 seconds, in one-second increments. Or, set the timer to 0 (disabled) if you want the menus to remain on-screen indefinitely.

•Film Mode: Use Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the Vision 120 detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to enable Film Mode (ON) to ensure stable processing for that source.

•CUE (Chroma Upsampling Error) Correction: Some DVD players use MPEG decoders that do not correctly “upsample” the 4:2:0 format chroma information on the DVD to the 4:2:2 or 4:4:4 format required by the video encoder of the display device.

This so-called “chroma bug” sometimes causes streaky or spiky horizontal lines running through the chroma channel. It is most noticeable in static, interlaced scenes and on diagonal edges (especially red ones). Set CUE to On to correct this issue.

•Motion Threshold: The Motion Threshold determines the difference between a pixel and its corresponding value in the previous field or frame that must be exceeded for the pixel to be considered moving.

Increase the Motion Threshold if the image appears excessively noisy or if moving objects appear blurred. Decrease it to reduce or eliminate artifacts caused by deinterlacing errors.

•Altitude: Select Altitude from the Miscellaneous menu to control the operation of the projector’s cooling fan.

In most cases, the default setting (Normal) will maintain the correct operating temperature. If the lamp frequently turns off due to overheating, or in certain high-altitude operating environments, you may need to change this setting to High.

System Reset: To reset ALL projector and controller settings (including image settings) back to their factory defaults, choose System Reset from the Service menu.

A confirmation message appears, reminding you to save your settings before you perform the reset, so that you can restore them afterwards. If you have done this, select Confirm to continue with the reset. Otherwise, click Back to cancel.

This action is not undoable. Proceed with caution! Before you perform a Caution System Reset, save your “Custom” ISF presets (page 58) and ISF Day/Night

presets (page 60).

Restore Saved Settings: Following a System Reset, select Restore Saved Settings, then select Yes to apply all previously-saved settings to the projector and VHD Controller.

62

Vidikron Vision Model 120 Installation/Operation Manual

Page 75 Page 77
Image 76
Page 75 Page 77
Contents 120 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate OperationMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Vision 120 offers these key features and benefitsOptional Accessories Controls and Functions Vision 120 at a GlanceVision 120 Rear Panel Vision 120 Rear PanelUSB-B DVI-DL Dual-LinkVHD Controller Front Panel VHD Controller Front PanelIssue LED Service only For future use VHD Controller Rear PanelDVI-DL DUAL-LINK Output 1080p RS-232/485 Control PortHdmi I 1 / Hdmi II 2 Digital 10. HD3 InputVision 120 Remote Control Vision 120 Remote ControlPicture Adjustment Buttons BRT Brightness On / OFFSource Selection Buttons VID S-VideoMemory Preset Buttons Aspect Ratio Selection Buttons169 Lbox LetterboxRemote Control 3InstallationOperation Quick Setup Installation OverviewStep Procedure For Details, Refer to If installing a Vision 120/CineWide or VisionInstallation Considerations Projector Installation OptionsInstallation Type Advantages ConsiderationsVision 120 Lens Options and Throw Ratios Ceiling Installation Floor InstallationVertical and Horizontal PositionHorizontal Lens Shift Example only Vision 120 Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Adjusting the Projection Mounting the VisionFloor Mounting Upright Ceiling Mounting Inverted AngleConnecting the VHD Connector Panel AccessConnections to the Vision 120 and VHD Controller Connecting Source ControllerHdmi Connections See Figure Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 16. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentVHD Controller Connecting an External IR Receiver to the VHD ControllerRear Panel Adjusting the Picture Orientation Turning on the PowerPower source Focus Primary Lens AdjustmentsZoom Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using the On-Screen Menus 4OperationMemory Presets ServiceInput Source Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Description169 Hdtv programs in their nativePicture PicturePerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionMemory Presets Memory PresetsInformation InformationCalibration ISF Night CalibrationISF Day OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, aboveService ServiceHD Format Presets 5Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Troubleshooting Chart Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command Syntax6Serial Communications Serial Commands and Responses Command Description ResponseInput Selection Commands Aspect Ratio CommandsCommand Description Response Image Preset Commands Menu Navigation CommandsPicture Adjust Commands Enter or Select buttonSerial Communications 7Specifications Vision 120 SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsVHD Controller Specifications Vision 120 Dimensions Vision 120/CineWide with AutoScope DimensionsSupported Signal Timings by Input Supported TimingsFormat Resolution Frequency HD 1/HD 2/HD Page Vidikron
Top Page Image Contents