Vidikron Vision 120 operation manual Service, HD Format

Page 75

Operation

Use the Service menu to access advanced projector configuration settings. This menu should be used by ISF-certified technicians only.

You must enter a passcode to access the Service menu.

Note

Test Video: Select Test Video from the Service Menu to access the internal test patterns on

the Vision 120. Four patterns are available: Horizontal Ramp, Vertical Ramp, Color Bars 1 (solid bars) and Color Bars 2 (SMPTE “checkerboard” pattern).

Press MENU to exit test pattern mode.

Tip

You can also use the PATTERN button on the projector rear panel or VHD

Controller front panel to enter and exit test pattern mode.

Service

Service

Test Video

Display Device

HD Format

Triggers

Miscellaneous

System Reset

Restore Saved Settings

Display Device: The options in the Display Device menu allow you to change the picture orientation and perform lens adjustments.

•Installation: Select Installation from the Display Device menu to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

•Lens: Select Lens from the Display Device menu to access the motorized lens controls. Refer to Primary Lens Adjustments on page 41.

•Lamp Info: Select Lamp Info from the Display Device menu to obtain information about

the currently-installed lamp: its serial number, number of “strikes” (attempts to ignite) and number of hours in use.

•Diagnostic: Select Diagnostic from the Display Device menu, then select Red, Green, Blue, Yellow, Cyan or Magenta to display only that color (simulating a filter of that color). This can be useful for calibration or measurement purposes.

To restore the normal picture (all colors), select White.

HD Format: Select HD Format from the Service menu to choose the default color space for the source signals on the HD1, HD2 and HD3 inputs. Select COMP (component) or RGB. The VHD Controller assumes this color space when you “direct-select” an HD input using the left-arrow and right-arrow ( or ) buttons on the projector rear panel or VHD Controller front panel, or the HD1, HD2 or HD3 buttons on the remote control unit.

You can override this setting by using the OSD to select an HD input (refer to Input Source on page 51). For example, if you select COMP for HD2 here and the input signal changes to RGB, select “RGB BNC” from the Input Source menu to enable the Vision 120 to properly display that signal.

When you change the default color space for an HD input, it takes effect

Note

the next time you select that input (not immediately).

 

HD Format

HD1

7 COMP

… RGB

HD2

7 COMP

… RGB

HD3

… COMP

7 RGB

Vidikron Vision Model 120 Installation/Operation Manual

61

Page 74 Page 76
Image 75
Page 74 Page 76
Contents 120 Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Vidikron Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part 1Table of Contents Operation Attach Lens Mounting Assembly to Lens Motor Carriage PlateMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv About This Manual 1IntroductionIf you need Turn to Using This ManualVision 120 offers these key features and benefits Description, Features and BenefitsOptional Accessories Vision 120 at a Glance Controls and FunctionsVision 120 Rear Panel Vision 120 Rear PanelDVI-DL Dual-Link USB-BVHD Controller Front Panel VHD Controller Front PanelIssue LED RS-232/485 Control Port Service only For future useVHD Controller Rear Panel DVI-DL DUAL-LINK Output 1080p10. HD3 Input Hdmi I 1 / Hdmi II 2 DigitalVision 120 Remote Control Vision 120 Remote ControlVID S-Video Picture Adjustment Buttons BRT BrightnessOn / OFF Source Selection ButtonsLbox Letterbox Memory Preset ButtonsAspect Ratio Selection Buttons 1693Installation Remote ControlOperation If installing a Vision 120/CineWide or Vision Quick SetupInstallation Overview Step Procedure For Details, Refer toAdvantages Considerations Installation ConsiderationsProjector Installation Options Installation TypeVision 120 Lens Options and Throw Ratios Position Ceiling InstallationFloor Installation Vertical and HorizontalHorizontal Lens Shift Example only Folded Optics Vision 120 Vertical and Horizontal Lens Shift LimitsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Angle Adjusting the ProjectionMounting the Vision Floor Mounting Upright Ceiling Mounting InvertedConnector Panel Access Connecting the VHDConnections to the Vision 120 and VHD Controller Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with Connecting SourceController Hdmi Connections See Figure12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 14. Analog RGB Connections Analog Computer RGB Connections See FigureDVD Player, VCR Satellite Receiver Laser Disc etc Video/Composite Video Connections See Figure16. RS-232 Control System Connection ConnectionEquipment Connecting 12-Volt TriggerConnecting an External IR Receiver to the VHD Controller VHD ControllerRear Panel Turning on the Power Adjusting the Picture OrientationPower source Primary Lens Adjustments FocusZoom Plate fixed CineWide Installing and Adjusting the CineWide Anamorphic Lens20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation 4Operation Using the On-Screen MenusAspect Ratio Memory PresetsService Input SourceMain Menu Input SourceAspect Ratio Hdtv programs in their native Aspect Ratio SettingsDescription 169Picture PictureTypical Pluge Pattern for Adjusting Brightness Perform the adjustments in the order listed hereGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationCalibration Calibration ISF NightISF Day Gain/Offset Refer to ISF Night Display Color, above OSD Position To adjust the menu and press Enter orService ServiceHD Format Presets Lamp Replacement 5Maintenance and TroubleshootingFilter Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port Configuration6Serial Communications Aspect Ratio Commands Serial Commands and ResponsesCommand Description Response Input Selection CommandsEnter or Select button Command Description Response Image Preset CommandsMenu Navigation Commands Picture Adjust CommandsSerial Communications Vision 120 Specifications 7SpecificationsDimensions Home Theater Calibration SpecificationsIndustry-Standard Specifications Power RequirementsVHD Controller Specifications Vision 120/CineWide with AutoScope Dimensions Vision 120 DimensionsSupported Timings Supported Signal Timings by InputFormat Resolution Frequency HD 1/HD 2/HD Page Vidikron
Top Page Image Contents