Vidikron Vision 120 Turning on the Power, Adjusting the Picture Orientation, Power source

Page 54

Installation

Connecting to AC Power ➤ Projector/VHD Controller: Plug the female end of one power cord into the AC receptacle on the rear of the Vision 120 (AC 100V ~ 240V). Then, connect the other end to your AC power source.

Similarly connect the VHD Controller to a nearby AC outlet.

AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power cord is provided for the lens motor. Plug the female end of the AC power cord into the AC input on the rear of the lens motor assembly. Connect the other end to a 110 VAC power source.

Caution	The input voltage to the AutoScope lens motor must be between 100 and
Caution	120 VAC. Do not connect the AutoScope lens motor to a 200-240 VAC
	power source!

3.8

Turning on the Power

1.Turn on your source components.

2.Turn on the main power switch at the rear of the VHD Controller.

3.If this is an AutoScope-equipped projector, turn on the main power switch at the rear of the AutoScope lens motor. The lens motor power switch is located next to the AC input (see Figure 3-17).

4.Press the ON button on the remote control – or the SOFT PWR button on the VHD Controller front panel – to turn on the system. The vacuum fluorescent display on the VHD Controller front panel briefly displays “Starting Display.”

5.When the projector is ready for use (after about 20 seconds), the RUN LED on the VHD Controller front panel lights solid blue. The fluorescent display indicates the current input source, aspect ratio and input resolution; for example:

Current Input Source

3.9

Adjusting the Picture Orientation

	V120				Component RCA
16:9					480I


Aspect Ratio				Input Resolution

By default, the Vision 120 is configured for a “floor/front” installation, in which the projector is installed upright and in front of the screen. If it is installed behind the screen and/or inverted, you must change the picture orientation. To do this:

1.Press MENU.

2.Select Service from the Main Menu and enter the Service Menu passcode.

3.Select Display Device from the Service Menu.

4.Select Installation from the Display Device menu.

5.Choose Floor Rear, Ceiling Front or Ceiling Rear, to match the installation method.

40	Vidikron Vision Model 120 Installation/Operation Manual

Image 54

Contents 120 Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Vidikron Important Safety Instructions Compliance Information Declaration of ConformityFCC Part 1Table of Contents Attach Lens Mounting Assembly to Lens Motor Carriage Plate OperationMaintenance and Troubleshooting Table of Contents Xii 1List of Figures List of Figures Xiv 1Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Vision 120 offers these key features and benefitsOptional Accessories Controls and Functions Vision 120 at a GlanceVision 120 Rear Panel Vision 120 Rear PanelUSB-B DVI-DL Dual-LinkVHD Controller Front Panel VHD Controller Front PanelIssue LED DVI-DL DUAL-LINK Output 1080p Service only For future useVHD Controller Rear Panel RS-232/485 Control PortHdmi I 1 / Hdmi II 2 Digital 10. HD3 InputVision 120 Remote Control Vision 120 Remote ControlSource Selection Buttons Picture Adjustment Buttons BRT BrightnessOn / OFF VID S-Video169 Memory Preset ButtonsAspect Ratio Selection Buttons Lbox Letterbox3Installation Remote ControlOperation Step Procedure For Details, Refer to Quick SetupInstallation Overview If installing a Vision 120/CineWide or VisionInstallation Type Installation ConsiderationsProjector Installation Options Advantages ConsiderationsVision 120 Lens Options and Throw Ratios Vertical and Horizontal Ceiling InstallationFloor Installation PositionHorizontal Lens Shift Example only Vision 120 Vertical and Horizontal Lens Shift Limits Folded OpticsInstalling the Primary Projection Lens Disconnection or lens damage Installing the Optional CineWide Lens Mount 6shows the Vision 120/CineWide with AutoScope motor assembly Remove Vision 120 with Ceiling Mount Adapters/Projector Stands AutoScope Lens Motor Installation Installing the Fixed CineWide Base Plate Vision 120/CineWide Floor Mounting Upright Ceiling Mounting Inverted Adjusting the ProjectionMounting the Vision AngleConnector Panel Access Connecting the VHDConnections to the Vision 120 and VHD Controller Hdmi Connections See Figure Connecting SourceController Hdmi Source HD-DVD/BD/DVD Player or HD Tuner with12. Digital DTV RGB or Component Video Connections HD1, HD2 13. Digital DTV RGB or Component Video Connections HD3 Analog Computer RGB Connections See Figure 14. Analog RGB ConnectionsVideo/Composite Video Connections See Figure DVD Player, VCR Satellite Receiver Laser Disc etcConnection 16. RS-232 Control System ConnectionConnecting 12-Volt Trigger EquipmentConnecting an External IR Receiver to the VHD Controller VHD ControllerRear Panel Turning on the Power Adjusting the Picture OrientationPower source Primary Lens Adjustments FocusZoom Installing and Adjusting the CineWide Anamorphic Lens Plate fixed CineWide20. Attaching the Anamorphic Lens to the Lens Adapter Ring Too Far Left Correct position Too Far Right Installation Anamorphic Lens Top View Adjusting the Geometry Installation Using the On-Screen Menus 4OperationInput Source Memory PresetsService Aspect RatioMain Menu Input SourceAspect Ratio 169 Aspect Ratio SettingsDescription Hdtv programs in their nativePicture PicturePerform the adjustments in the order listed here Typical Pluge Pattern for Adjusting BrightnessGray Yellow Cyan Green Magenta Red Blue Gray Yellow Cyan Green Magenta Red Blue Input Position Input PositionInformation Memory PresetsMemory Presets InformationCalibration Calibration ISF NightISF Day OSD Position To adjust the menu and press Enter or Gain/Offset Refer to ISF Night Display Color, aboveService ServiceHD Format Presets 5Maintenance and Troubleshooting Lamp ReplacementFilter Replacement Troubleshooting Tips Troubleshooting ChartSymptom Possible Causes Solution Maintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port Configuration6Serial Communications Input Selection Commands Serial Commands and ResponsesCommand Description Response Aspect Ratio CommandsPicture Adjust Commands Command Description Response Image Preset CommandsMenu Navigation Commands Enter or Select buttonSerial Communications 7Specifications Vision 120 SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsVHD Controller Specifications Vision 120 Dimensions Vision 120/CineWide with AutoScope DimensionsSupported Signal Timings by Input Supported TimingsFormat Resolution Frequency HD 1/HD 2/HD Page Vidikron