TANDBERG TC3.0 manual Standby settings Standby settings, Standby BootAction Standby WakeupAction

Page 28

TANDBERG Codec C90 and Profiles using C90

Administrator guide

ContentsContents

IntroductionIntroduction

AdvancedAdvancedAdvancedconfigurationconfigurationconfig.

PassPasswordord protectionprotection

AboutAboutmonitorsonitors

AudioAudiomattersat ers

AppendicesAppendices

ContactContactusus

The Standby settings

The Standby settings, cont...

Standby BootAction

Standby WakeupAction

Decide what the system is going to do on boot.

Decide what the system is going to do when leaving standby mode.

Valuespace: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/

Valuespace: <None/Preset1/Preset2/Preset3/Preset4/Preset5/Preset6/Preset7/Preset8/

Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/

Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/RestoreCameraPosition/

DefaultCameraPosition>

DefaultCameraPosition>

None: No action.

None: No action.

Preset 1..15: Activate the selected preset.

Preset 1..15: Activate the selected preset.

RestoreCameraPosition: Set the camera to the position it had before the last boot.

RestoreCameraPosition: Set the camera to the position it had before entering standby.

DefaultCameraPosition: Set the camera to the factory default position.

DefaultCameraPosition: Set the camera to the factory default position.

Example: Standby BootAction: DefaultCameraPosition

Example: Standby WakeupAction: RestoreCameraPosition

Standby Control

Determine whether the system should go into standby mode or not.

Valuespace: <On/Off>

On: Enter standby mode when the Standby Delay has timed out. Requires the Standby Delay to be set to an appropriate value.

Off: Not entering standby mode.

Example: Standby Control: On

Standby Delay

Define how long (in minutes) the system shall be in idle mode before it goes into standby mode. Requires the Standby Control to be enabled.

Valuespace: <1..480>

Range: 1-480 minutes

Example: Standby Delay: 10

Standby StandbyAction

NEW TC2.1 Decide what the system is going to do when going into standby mode.

Valuespace: <None/PrivacyPosition>

None: No action.

PrivacyPosition: Turns the camera to a sideways position for privacy.

Example: Standby StandbyAction: PrivacyPosition

D14635.02—MARCH 2010

28

www.tandberg.com

Image 28
Contents For Tandberg Codec C90 and Profile 65 Dual using C90 ContentsContents IntroductionIntroductionTable of Contents This guide?Document revision history Introduction ChapterIntroduction Purpose of this documentDisclaimers and Notices Products covered in this guideSoftware release notes New features and improvements What’s new­in this versionUser documentation Improved web interfaceIntegrator benefits Audio enhancementsCamera Tandberg Profile 65 Dual at a glance Design Features Application FeaturesPerformance Features Tandberg Codec C90 at a glanceAdvanced configuration settings Description of the advanced configuration settings Audio settingsAudio settings, Audio Input Microphone 1. Mode Audio Output Hdmi 1, 3 ModeAudio Output Line 1. Equalizer Mode Audio Input Microphone 1. VideoAssociation VideoInputSourceAudio Output Line 1. Mode Audio SoundsAndAlerts RingVolumeAudio Volume Audio SoundsAndAlerts KeyTones ModeCamera settings Camera settings,Cameras Camera 1. Whitebalance Mode Cameras Camera 1. IrSensorCameras Camera 1. Mirror Cameras Camera 1. DhcpConference settings Conference settings,Conference 1. DefaultCall Protocol Conference 1. VideoBandwidth PresentationChannel WeightConference 1. DefaultCall Rate Conference 1. VideoBandwidth ModeGpio settings H323 settings Gpio Pin 1. ModeH323 Profile 1. Authentication LoginName H323 Profile 1. Authentication PasswordH323 settings, Network settings Network settings,Network 1. IEEE8021X Mode Network 1. IEEE8021X PasswordNetwork 1. IPv4 QoS Mode Network 1. IPv4 AddressNetwork 1. IPv4 QoS Diffserv Signalling Network 1. TrafficControl ModeNetwork 1. IPv4 QoS Diffserv Video Network 1. MTUNetworkServices settings NetworkServices settings,Phonebook settings Provisioning settings SerialPort settingsSIP settings SIP settings,Standby settings Standby settings, Standby BootAction Standby WakeupActionStandby Delay Standby ControlSystemUnit settings Time settingsTime settings, Video settingsVideo settings, Video Input Source 1. OptimalDefinition Profile Video Input Source 1. OptimalDefinition Threshold60fpsVideo Input Source 1. Quality Video Layout ScaleToFrameVideo OSD Mode Video Layout ScaleToFrameTresholdVideo OSD InputMethod InputLanguage Video Layout ScalingVideo Output Hdmi 1, 3 Resolution Video OSD TodaysBookingsVideo Output Hdmi 1, 3 MonitorRole Video Output Hdmi 1, 3 OverscanLevelVideo Output DVI 2, 4 Resolution Video Output Composite 5 ResolutionVideo Output Composite 5 MonitorRole Video Output Composite 5 OverscanLevelExperimental menu Experimantal menu,Password protection Setting the codec administrator password Password protectionSetting the menu password About monitors About monitors when you have a Codec C90 Main monitorDual monitors # * # 0 2 #Audio matters Dynamic audio API ExampleEqualizer Audio Console applicationEqualizer filter parameters Filter typesMicrophone reinforcement Using microphone reinforcement in a large roomZone Examples of local stereo configuration StereoStereo in point to point call Stereo in MultisiteAppendices Optimal Definition Profiles High 720p60Medium w576p60 Normal w448p60Configure the video inputs Default configurationsVideo Input Matrix About the matrixTandberg Dnam for ProfileDnam Amplifier Dnam LoudspeakerCE Declarations Tandberg Profile using Codec C90Tandberg Codec C90 China RoHS table Current RFCs and drafts supported in SIP Supported RFCs in SIPMedia capabilities supported in SIP Technical specifications Tandberg Profile 65 DualProtocols Tandberg Codec C90 Watts max. for codec and main camera Headquarters European Headquarters Tandberg