Network 1. IEEE8021X Mode, Network 1. IPv4 Address

TANDBERG Codec C90 and Profiles using C90

Administrator guide

ContentsContents

IntroductionIntroduction

AdvancedAdvancedAdvancedconfigurationconfigurationconfig.

PassPasswordord protectionprotection

AboutAboutmonitorsonitors

AudioAudiomattersat ers

AppendicesAppendices

ContactContactusus

The Network settings, cont...

Network [1..1] IEEE8021X Mode

The system may be connected to an IEEE 802.1X LAN network with a port-based network access control that is used to provide authenticated network access for Ethernet networks.

Valuespace: <On/Off>

On: The 802.1X authentication is enabled.

Off: The 802.1X authentication is disabled. Default mode is Off.

Example: Network 1 IEEE8021X Mode: Off

Network [1..1] IEEE8021X Password

The 802.1X Password is the password needed for 802.1X authentication.

Valuespace: <S: 0, 32>

Format: String with a maximum of 32 characters.

Example: Network 1 IEEE8021X Password: “***”

Network [1..1] IPv4 Address

Defines the Static IP address for the system. Only applicable if Static IP assignment is chosen.

Valuespace: <S: 0, 64>

Format: Compact string with a maximum of 64 characters.

Example: Network 1 IPv4 Address: “10.47.5.100”

Network [1..1] IPv4 Gateway

Defines the IP default gateway. Only applicable if Static IP assignment is chosen.

Valuespace: <S: 0, 64>

Format: Compact string with a maximum of 64 characters.

Example: Network 1 IPv4 Gateway: “10.47.5.100”

Network [1..1] IPv4 SubnetMask

Defines the IP subnet mask. Only applicable if Static IP assignment is chosen.

Valuespace: <S: 0, 64>

Format: Compact string with a maximum of 64 characters.

Example: Network 1 IPv4 SubnetMask: “255.255.255.0”

The Network settings, cont...

Network [1..1] IPv4 QoS Mode

Defines whether IP Diffserv QoS should be used. The QoS (Quality of Service) is a method which handles the priority of audio, video and data in the network. The QoS settings must be supported by the infrastructure. DiffServ (Differentiated Services) is a computer networking architecture that specifies a simple, scalable and coarse-grained mechanism for classifying, managing network traffic and providing QoS priorities on modern IP networks.

Valuespace: <Off/Diffserv>

Off: When set to Off no QoS method is used.

Diffserv: Select Diffserv and then go to the Diffserv sub-menus (Audio, Data, Signalling and Video) to configure these settings.

Example: Network 1 IPv4 QoS Mode: diffserv

Network [1..1] IPv4 QoS Diffserv Audio

The DiffServ Audio setting is used to define which priority Audio packets should have in an IP network. Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority. These priorities might be overridden when packets are leaving the network controlled by the local network administrator.

Valuespace: <0..63>

Audio: A recommended value is DiffServ Code Point (DSCP) is AF41, which equals the value 34. If in doubt, contact your network administrator.

Example: Network 1 IPv4 QoS Diffserv Audio: 0

Network [1..1] IPv4 QoS Diffserv Data

The DiffServ Data setting is used to define which priority Data packets should have in an IP network. Enter a priority, which ranges from 0 to 63 for the packets. The higher the number, the higher the priority. These priorities might be overridden when packets are leaving the network controlled by the local network administrator.

Valuespace: <0..63>

Data: A recommended value is DiffServ Code Point (DSCP) AF23, which equals the value 22. If in doubt, contact your network administrator.

Example: Network 1 IPv4 QoS Diffserv Data: 0

D14635.02—MARCH 2010