Runco VX-2IX Home Theater Calibration Specifications, Industry-Standard Specifications, Lamp

Page 70

Specifications

Table 7-1. VX-2ix Specifications (continued)

Brightness and Contrast:

Cinema Standards Measurement System (CSMS)

 

Specifications

 

-

Brightness: 52.1 foot-Lamberts (fL)

 

-

Contrast Ratio: 271:1

 

These measurements are taken from the projector in a controlled,

 

home theater environment. All measurements are made to

 

ANSI/NAPM IT7.228-1997 specifications using the Photo Research

 

PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,

 

Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The

 

projector is calibrated to a color temperature of 6,500K and has a

 

minimum of 150 hours of usage.

 

The foot-Lambert (fL) is the unit of measurement used in commercial

 

movie theaters to express image brightness at the screen surface. The

 

Society of Motion Picture and Television Engineers (SMPTE) specifies

 

16 fL as the target image brightness for film-based projectors using an

 

open gate (without film in the projector). More importantly, today

 

SMPTE specifies 12 fL as the target image brightness in Digital

 

Cinema theaters. The foot-Lambert measurement is dependent on

 

screen size, screen gain and projector light output.

 

Home Theater Calibration Specifications

 

-

Light Output: 1227 ANSI Lumens

 

-

Contrast Ratio: 271:1

 

These specifications are obtained by calibrating the projector as

 

described above for CSMS measurements.

 

Industry-Standard Specifications

 

-

Light Output: 2500 ANSI Lumens

 

-

Contrast Ratio: 3100:1

 

These are typical projector brightness and contrast specifications

 

found in most companies’ sales literature. Runco includes these

 

measurements in its literature to allow for direct comparison with other

 

manufacturers’ projectors. These measurements are typically taken at

 

9,000K to 13,000K to get expected performance data when the

 

projector is used in professional, commercial and industrial displays.

 

 

Lamp:

275 Watts

 

 

Estimated Lamp Life:

2000 hours

 

 

Inputs:

(1) Composite; (2) S-Video; (1) Component; (2) HD-R (Pr), G

 

(Y), B (Pb), H, V; (2) DVI w/HDCP

 

 

 

Control Options:

-

Built-in keypad

 

-

Discrete infrared remote

 

-

Serial commands via RS-232

 

 

Trigger Outputs:

(3) +12 VDC, each rated at 750 mA and thermal

 

fuse-protected

 

 

Bandwidth:

150 Mega Samples/Second (MSPS)

 

 

Power Requirements:

100 to 240 VAC (auto-sensing), 50/60 Hz, 610 Watts

 

 

Operating Environment:

41°F to 95°F (5°C to 35°C), 0% to 90% humidity

 

(non-condensing)

 

 

Dimensions:

See Figure 7-1

 

 

Weight (without lens):

84 lbs. (38.10 kg)

 

 

Regulatory Approvals:

Complies with FCC, CE C-Tick

 

 

 

58

Runco VX-2ix Owner’s Operating Manual

Page 69 Page 71
Image 70
Page 69 Page 71
Contents VX-2ix Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsAppendix A. VX-2ix Color Gamut Adjustment Table of Contents List of Figures List of Figures Xii Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Performance with this productOptional Accessories Controls and Functions VX-2ix at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVolt 750 mA Trigger Outputs Video 1 / S-VIDEOPower Input 100 to 240 VAC Connect the VX-2ix to power here Right ButtonVX-2ix Remote Control VX-2ix Remote ControlVideo On / OFFCursor Buttons Comp ComponentANA Anamorphic Memory Preset Buttons ISF NT NightAspect Ratio Selection Buttons 4X3 Standard 43Controls and Functions Installation Remote ControlQuick Setup Step Procedure For Details, Refer toInstallation Type Installation ConsiderationsAmbient Light Lens Throw Range Throw Ratio Inches, with Lens OptionLens Only Anamorphic Minimum Maximum Position Vertical and HorizontalLens Shift Vertical Lens Shift Example Only Installing the Optional CineWide Lens Folded Optics Other ConsiderationsMounting Connections to DVI Connections See FigureDigital DTV RGB or Component Video Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller ConnectionInput voltage to the AutoScope lens motor must be between To a 200-240 VAC power source120 VAC. Do not connect the AutoScope lens motor Adjusting the Picture Orientation Turning on the PowerOperation Using the On-Screen Menus Lens AdjustmentsFocus Zoom Shift Input Source ISF PresetsService Aspect RatioInput Source Main MenuAspect Ratio Aspect Ratio Settings Remote Aspect Ratio Control Description KeySelect Cinema to view Picture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Calibration Should be used by ISF-certified technicians onlyGain/Offset Refer to ISF Night Display Color, above Service Do not change the Type setting in this menu HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV ADC Bandwidth Auto YPbPr Input ResolutionAuto Operation Operation Lens Replacement Maintenance and TroubleshootingLamp Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Maintenance and Troubleshooting Maintenance and Troubleshooting Troubleshooting Tips Symptom Possible Causes SolutionMaintenance and Troubleshooting Command RS-232 Connection and Port ConfigurationSerial Command Syntax Value Description Min/max Stored? Power On/Off CommandsAspect Ratio Commands Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift Commands Bkgnd Serial Communications Specifications VX-2ix SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsLimited Warranty Specifications are subject to change without noticeVX-2ix Dimensions VX-2ix DimensionsAppendix A. VX-2ix Color Gamut Adjustment Figure A-1. CIE 1931 Chromaticity DiagramSerial Connections Equipment Setup Required Hardware SoftwareCommand Parameter Value Description Min/max Figure A-3. VX-2ix Secondary RS-232 PortAdjusting the Gamut Command Parameter Value Description Min/max Stored?VX-2ix Color Gamut Adjustment VX-2ix Color Gamut Adjustment Page RUMA-011155
Related manuals
Manual 80 pages 32.98 Kb
Top Page Image Contents