Runco VX-2IX manual Do not change the Type setting in this menu

Page 53

Operation

Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the VX-2ix will respond. By default, both are set to 17. You can change these codes if either:

•Another device in the theater (a DVD player, for example) is responding to commands from the VX-2ix remote control in ways that are unpredictable or undesirable.

•You have multiple VX-2ix projectors and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific projector.

Tip

Use the rear-panel keypad to change a projector IR code. Then,

change the code sent by the remote to match as described below.

Do not change the “Type” setting in this menu.

Note

When you change a remote code on the VX-2ix, you must re-program your remote control to send that same code. To do this:

1. Using a straightened paper clip or similar object, press and hold the CODE button on the remote control for approximately three seconds, or until the red LED on the remote lights solid red.

2. Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.”

3.The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code.

Display Device: The options in the Display Device menu allow you to change the picture orientation, reset the lamp timer, perform lens adjustments and access additional test patterns.

•Installation: Select Installation from the Display Device menu to change the picture orientation to suit the method of installation (Floor Front, Floor Rear, Ceiling Front or Ceiling Rear).

This menu page also displays the number of hours that the lamp has been in service,

and lets you reset the counter (which is recommended after you replace the lamp; refer to Lamp Replacement on page 45).

•Lens: Select Lens from the Display Device menu to access the motorized lens controls. Refer to Lens Adjustments on page 28.

•Diagnostics: Select Diagnostics from the Service menu to access additional test patterns for calibration or measurement purposes:

•Select Red, Green or Blue to display only the selected color (simulating a filter of that color).

•Select 75 or 100 to display color bars (75 IRE or 100 IRE).

•Select Horz or Vert to display a horizontal or vertical gray ramp.

•Select Checks to display a 15-segment checkerboard pattern.

•Select Align to display a white grid against a black background (useful for verifying proper image or screen alignment).

Runco VX-2ix Owner’s Operating Manual

41

Page 52 Page 54
Image 53
Page 52 Page 54
Contents VX-2ix Page For Projectors, Video Processors and Controllers TWO Year Limited WarrantyEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsAppendix A. VX-2ix Color Gamut Adjustment Table of Contents List of Figures List of Figures Xii About This Manual IntroductionIf you need Turn to Using This ManualPerformance with this product Description, Features and BenefitsOptional Accessories VX-2ix at a Glance Controls and FunctionsHD1 / HD2 Analog BNC connectors Component Video RCA connectorsVideo 1 / S-VIDEO Volt 750 mA Trigger OutputsRight Button Power Input 100 to 240 VAC Connect the VX-2ix to power hereVX-2ix Remote Control VX-2ix Remote ControlCursor Buttons On / OFFVideo Comp ComponentAspect Ratio Selection Buttons Memory Preset Buttons ISF NT NightANA Anamorphic 4X3 Standard 43Controls and Functions Remote Control InstallationStep Procedure For Details, Refer to Quick SetupAmbient Light Installation ConsiderationsInstallation Type Lens Only Anamorphic Minimum Maximum Throw Range Throw Ratio Inches, with Lens OptionLens Lens Shift Vertical and HorizontalPosition Vertical Lens Shift Example Only Folded Optics Other Considerations Installing the Optional CineWide LensMounting DVI Connections See Figure Connections toDigital DTV RGB Connections Digital DTV RGB or Component Video Connections See FigureAnalog RGB Connections Analog Computer RGB Connections See FigureComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 Controller120 VAC. Do not connect the AutoScope lens motor To a 200-240 VAC power sourceInput voltage to the AutoScope lens motor must be between Operation Turning on the PowerAdjusting the Picture Orientation Focus Zoom Shift Lens AdjustmentsUsing the On-Screen Menus Service ISF PresetsInput Source Aspect RatioAspect Ratio Main MenuInput Source Remote Aspect Ratio Control Description Key Aspect Ratio SettingsSelect Cinema to view Picture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan Input PositionInformation ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Should be used by ISF-certified technicians only CalibrationGain/Offset Refer to ISF Night Display Color, above Service Do not change the Type setting in this menu Auto ADC Bandwidth Auto YPbPr Input ResolutionHD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Operation Lamp Replacement Maintenance and TroubleshootingLens Replacement Only trained, authorized Runco dealers should attempt toMaintenance and Troubleshooting Maintenance and Troubleshooting Maintenance and Troubleshooting Symptom Possible Causes Solution Troubleshooting TipsMaintenance and Troubleshooting Serial Command Syntax RS-232 Connection and Port ConfigurationCommand Value Description Min/max Stored? Power On/Off CommandsAspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Serial Communications VX-2ix Specifications SpecificationsIndustry-Standard Specifications Home Theater Calibration SpecificationsPower Requirements DimensionsSpecifications are subject to change without notice Limited WarrantyVX-2ix Dimensions VX-2ix DimensionsFigure A-1. CIE 1931 Chromaticity Diagram Appendix A. VX-2ix Color Gamut AdjustmentRequired Hardware Software Serial Connections Equipment SetupFigure A-3. VX-2ix Secondary RS-232 Port Command Parameter Value Description Min/maxCommand Parameter Value Description Min/max Stored? Adjusting the GamutVX-2ix Color Gamut Adjustment VX-2ix Color Gamut Adjustment Page RUMA-011155
Related manuals
Manual 80 pages 32.98 Kb

VX-2IX specifications

The Runco VX-2IX is a high-end projector designed for home theater enthusiasts seeking an unparalleled cinematic experience. Leveraging sophisticated technology, this model embodies a perfect blend of precision, performance, and aesthetic elegance.

At the core of the Runco VX-2IX is its advanced DLP (Digital Light Processing) technology, which provides remarkable color accuracy and sharpness. This projector boasts a native resolution of 1080p, ensuring that every image displayed is filled with stunning detail and clarity. Furthermore, the projector supports 4K video signals, making it a future-proof choice for viewers ready to embrace the latest in video technology.

One of the standout features of the VX-2IX is its proprietary Runco Infinity Processing, which enhances image quality by optimizing the processing of video signals. This technology significantly reduces motion blur, resulting in smooth, fluid visuals, even during fast-paced scenes. For those who cherish deep, rich blacks in their viewing experience, the VX-2IX also incorporates Runco’s unique Dynamic Black technology. This feature adjusts the projector’s lamp output in real-time, providing exceptional contrast ratios that elevate the overall viewing experience.

The projector's brightness is rated at 1200 ANSI lumens, making it suitable for various room environments, including spaces with moderate ambient light. Coupled with a high-quality color wheel, the projector produces vibrant and true-to-life colors, enhancing the depth and realism of every scene.

Another pivotal aspect of the Runco VX-2IX is its flexible installation options. The device offers extensive lens shift and zoom capabilities, allowing it to be adapted easily to different screen sizes and viewing conditions. This versatility means that whether you’re mounting the projector on a ceiling or placing it on a shelf, you can achieve the optimal projection distance and image size effortlessly.

The Runco VX-2IX is also equipped with an intuitive user interface that provides quick access to a variety of settings, including color calibration and image adjustments. This level of customization allows users to tailor their viewing experience to their specific preferences, resulting in a polished and personalized setup.

In conclusion, the Runco VX-2IX is a premier choice for discerning home theater aficionados. With its impressive resolution, advanced processing technologies, and versatile installation options, this projector delivers an exceptional viewing experience that captivates and transports audiences to new cinematic heights. Whether watching a blockbuster film or enjoying a home video, the VX-2IX stands as a beacon of quality and innovation in the realm of home entertainment.
Top Page Image Contents