Runco CX-65HD, CX-OPAL47, CX-47HD operation manual Characteristics of the incoming signal, Setup

Page 49

Sleep Timer: Use the Sleep Timer to turn off the Crystal Series LCD after a specified interval.

To set the Sleep Timer:

Select Sleep Timer from the Timer menu and press ENTER.

– OR –

Press the TIMER OFF button on the remote control.

Use the right- or left-arrow button to select 10, 30, 60, 120 or 180 minutes. Then, press ENTER or MENU.

Use the controls in the Setup menu to perform advanced image quality adjustments and access various other Crystal Series LCD features.

OSD Language: Select OSD Language from the Setup menu and press ENTER. Then, use the up- or down-arrow buttons to select the OSD language (English, French, Spanish, Portuguese or German). Press ENTER again to confirm your selection.

OSD Timer: Use the or button to set the OSD Timer. This timer controls how long the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in

10-second increments. When you set the OSD to 0, the menus remain on-screen until you hide them by pressing EXIT.

PC Mode Adjust: To improve the quality of displayed images from a computer or other VESA-compliant, RGB (480p or higher) source, select PC Mode Adjust and press

ENTER.

Auto Adjust: Auto Adjust automatically adjusts settings to optimize computer images. To execute Auto Adjust on command, select Auto Adjust and press ENTER.

Note

Auto Adjust may take some time to complete, depending on the

characteristics of the incoming signal.

Clock: Use the up- or down-arrow buttons ( , ) to highlight Clock. Then, use the right-arrow button ( ) to increase the pixel clock rate; use the left-arrow button ( ) to decrease it.

Phase: Adjust the phase if the image shows shimmer or “horizontal noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the incoming signal. The effect of this control is similar to that of a tracking control on a VCR.

For best results, use a good test pattern such as a smooth gray consisting of a clear pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may notice that you can stabilize the image at more than one point. Use either setting in this case.)

H Position: Use the up- or down-arrow buttons ( , ) to highlight H Position. Then, use the right-arrow button ( ) to shift the image to the right; use the left-arrow button ( ) to shift the image to the left.

V Position: Use the up- or down-arrow buttons ( , ) to highlight V Position. Then, use the right-arrow button ( ) to shift the image up; use the left-arrow button ( ) to shift the image down.

To restore the factory-default Clock, Phase and Position settings, select Factory Reset and press ENTER.

Setup

Setup

OSD Language OSD Timer

PC Mode Adjust

Overscan

Letterbox Mode

HDMI Audio Input

Film Mode Auto Backlight

HDMI CSC

Baud Rate

SCART

Source Enable

LED Option

System Info

CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual

35

Image 49
Contents CX-47HD CX-OPAL47 CX-65HD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents ISF Calibration List of Figures List of Figures About This Manual IntroductionTip Using This ManualKey Features and Benefits Parts List Description, Features and BenefitsIntroduction Controls and Functions Controls and IndicatorsCrystal Series LCD at a Glance Handles Model CX-47HD and CX-OPAL47 Inputs and Outputs Crystal Series LCD Inputs and OutputsModel CX-65HD Inputs and Outputs Speaker Output Left + Right VOL+ Crystal Series LCD Remote ControlRGB HD PIP Remote Control InstallationBattery Installation Installation Overview Quick SetupConnections to the Crystal Series LCD Installation ConsiderationsWall-Mounting the Crystal Series LCD Ambient LightSeries LCD to Source Sections that follow Components Connecting the CrystalAnalog RGB Connections VCR Speakers Optional Connecting ExternalDigital Audio Connection Receiver Connecting an External IRRS-232 Controller ConnectionInstallation Operation Turning on the PowerChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Crystal Series LCD OSD Menu Structure Source Main MenuAspect Ratio Aspect Ratio Settings Picture Adjust Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Operation Balance Equalizer Speaker Setup Characteristics of the incoming signalLetterbox Mode = Letterbox Hdmi 1 Hdmi 2 Hdmi 3 Hdmi 4 Scart Component RGB Video Menu should be used by ISF-certified technicians only Gain Crystal Series LCD Splash Screen Using Picture-In-Picture PIP Position Changing the PIPSwapping the Main and PIP Images Changing the PIP SizeOperation Cleaning Maintenance and TroubleshootingTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlMaintenance and Troubleshooting Serial Communications Serial CommandsS4E SDE 0001 0090 Personalizing the Splash Screen Using Serial CommandsSerial Communications Crystal Series LCD Specifications SpecificationsWeight including stand Regulatory Approvals Limited Warranty CX-47HD/CX-OPAL47 Dimensions Top/Front Crystal Series LCD DimensionsCX-47HD/CX-OPAL47 Dimensions Rear/Side CX-65HD Overall Dimensions Top/Front CX-65HD Overall Dimensions Rear/Side Supported Timings Supported Signal Timings by InputPAL Page 020-0969-00 Rev. B January
Related manuals
Manual 84 pages 22.58 Kb