Runco CX-65HD, CX-OPAL47, CX-47HD operation manual Serial Communications, Serial Commands

Page 61

6. Serial Communications

To interface the Crystal Series LCD with a home theater automation/control system or a PC running terminal emulation software (such as HyperTerminal, provided with Microsoft® Windows™), connect it to your control system or PC as shown in Figure 3-9.Use a straight-through cable.

Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to match that of the Crystal Series LCD RS-232 port. To check the baud rate setting, select Baud Rate from the Setup menu (refer to page 37).

Commands are in ASCII format and are not case-sensitive.

A carriage return is not required after a command.

To send a command from a PC running terminal emulation software, create a text file containing that command. Then, use the file transfer function in your terminal emulation program to send the command. (If you are using HyperTerminal, choose “Send Text File...” from the Transfer menu.)

When you send a valid command, the Crystal Series LCD executes it and acknowledges it with a right-bracket character (]) followed by the four-digit numeric code you sent; for example, ]0002.

When you send an invalid command (one followed by values outside the valid range for that command), the Crystal Series LCD ignores it and returns >MAX or <MIN instead of the four-digit code.

When you send an unrecognized/misspelled command, the Crystal Series LCD ignores it and returns -N/Ainstead of the four-digit code.

Table 6-1lists the RS-232 command set.

Table 6-1. Serial Commands

 

Command

 

Description

 

 

 

 

 

 

[

 

S3A

 

0###

Set audio volume to ### ( = 000-100)

 

 

 

 

Example: [S3A0075 sets volume to 75

 

 

 

 

 

 

[

 

+3A

 

 

Audio volume up

 

 

 

 

 

 

[

 

-3A

 

 

Audio volume down

 

 

 

 

 

 

[

 

S3E

 

000#

Audio mute

 

 

 

 

 

0 = not muted, 1 = muted

 

 

 

 

 

 

Example: [S3E0001 mutes the audio output

6.1

RS-232 Connection and Port Configuration

6.2

Serial Command Syntax

CX-47HD/CX-OPAL47/CX-65HD Installation/Operation Manual

47

Image 61
Contents CX-47HD CX-OPAL47 CX-65HD Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Page Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents ISF Calibration List of Figures List of Figures About This Manual IntroductionTip Using This ManualKey Features and Benefits Parts List Description, Features and BenefitsIntroduction Controls and Functions Controls and IndicatorsCrystal Series LCD at a Glance Handles Model CX-47HD and CX-OPAL47 Inputs and Outputs Crystal Series LCD Inputs and OutputsModel CX-65HD Inputs and Outputs Speaker Output Left + Right VOL+ Crystal Series LCD Remote ControlRGB HD PIP Remote Control InstallationBattery Installation Installation Overview Quick SetupConnections to the Crystal Series LCD Installation ConsiderationsWall-Mounting the Crystal Series LCD Ambient LightSeries LCD to Source Sections that follow Components Connecting the CrystalAnalog RGB Connections VCR Speakers Optional Connecting ExternalDigital Audio Connection Receiver Connecting an External IRRS-232 Controller ConnectionInstallation Operation Turning on the PowerChanging the OSD Language Setting the PC Display Properties Using the On-Screen Menus Crystal Series LCD OSD Menu Structure Source Main MenuAspect Ratio Aspect Ratio Settings Picture Adjust Typical Pluge Pattern for Adjusting Brightness Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Operation Balance Equalizer Speaker Setup Characteristics of the incoming signalLetterbox Mode = Letterbox Hdmi 1 Hdmi 2 Hdmi 3 Hdmi 4 Scart Component RGB Video Menu should be used by ISF-certified technicians only Gain Crystal Series LCD Splash Screen Using Picture-In-Picture PIP Position Changing the PIPSwapping the Main and PIP Images Changing the PIP SizeOperation Cleaning Maintenance and TroubleshootingTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlMaintenance and Troubleshooting Serial Communications Serial CommandsS4E SDE 0001 0090 Personalizing the Splash Screen Using Serial CommandsSerial Communications Crystal Series LCD Specifications SpecificationsWeight including stand Regulatory Approvals Limited Warranty CX-47HD/CX-OPAL47 Dimensions Top/Front Crystal Series LCD DimensionsCX-47HD/CX-OPAL47 Dimensions Rear/Side CX-65HD Overall Dimensions Top/Front CX-65HD Overall Dimensions Rear/Side Supported Timings Supported Signal Timings by InputPAL Page 020-0969-00 Rev. B January
Related manuals
Manual 84 pages 22.58 Kb