Sanyo TLS-9960 Normal Recording Before starting, Record Pause, Recording Speed Mode

Page 17

NORMAL RECORDING

Normal Recording

Before starting

œTurn the power on to all devices used.

œLoad a cassette tape with erasure-prevention tab.

NOTE:

œIf in the (SET UP 3) menu, TAPE IN MODE is set to “REC”, recording will start after the tape thread has been checked.

œSet the ON SCREEN switch to the “ON” position.

1Press the REC/PLAY SPEED l (or j) button to set the recording speed mode.

øThe recording speed mode is displayed on-screen and on the digital display.

2Press the REC button.

øThe record indicator “m” light.

øRecording starts.

øWhen the end of the tape is reached, “OFF” will be displayed.

NOTES:

œIf in the (SET UP 2) menu, in the BUZZER section TAPE END is set to “Y”, the buzzer will be heard as long as “OFF” is displayed on the digital display.

œTo cancel the “OFF” display, press the STOP, EJECT or PLAY button or turn the SHUTTLE ring.

œIf recording stops due to a problem with the tape or other reason, the unit will try once to resume recording. If the tape still does not advance, the VCR will go into stop mode.

3To stop recording, press the STOP button.

NOTES:

œA tape recording made on this VCR may not play back with the same degree of clarity on a time lapse from another manufacturer.

œIf you press on the REC button and the loaded cassette has no erasure-prevention tab, the VCR will eject the cassette.

[Recording Speed Mode]

 

Maximum

 

 

 

Recording

recording

Recording

Audio

 

speed mode

duration (with a

interval

Tape motion

recording

(hour mode)

T-120 cassette

(second)

 

 

 

 

tape) (hours)

 

 

 

2

2

1/60

Possible

Continuous

12

14

7/60

24

26

13/60

 

 

48

50

25/60

 

 

72

74

37/60

 

 

96

98

49/60

 

 

120

122

61/60

 

 

168

170

85/60

Not possible

Intermittent

240

242

121/60

360

362

181/60

 

 

480

482

241/60

 

 

720

722

361/60

 

 

960

962

481/60

 

 

000

—

60-180

 

 

Record Pause

Recording can be interrupted temporarily.

1Press the STILL/PAUSE button during recording.

øThe Pause/Still indicator “N” blinks.

NOTES:

œThe image appears on-screen but it is not recorded.

œIf a recording pause continues for 5 minutes or more, the VCR will go into stop mode to avoid damaging the tape.

2To resume recording, press the REC button, or press the STILL/PAUSE button again.

16

English

Page 16 Page 18
Image 17
Page 16 Page 18
Contents
TLS-9960 Precautions Contents FeaturesAccessory Front Panel Operation Indicators Locations of Controls and IndicatorsOperation Mode Indicator OFF indicatorRS485 B Back PanelConnections Power Cord InstallationAbout the memory reset Reference pages are shown in square brackets Types of ON-SCREEN Displays and Display SequenceTypes of ON-SCREEN Displays and Display Sequence Using the JOG dial and Shuttle ringJOG dial Shuttle ringSetting procedure is now completed Setting the Language and ClockDay of week is set automatically Last 2 digits only are displayedSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is Loaded Correct tape thread check function @@TIMING@@@@@@@@FIELDOperation Tape Management FunctionIf no tape management data is present on the tape If tape management data is present on the tapeTape MANAGE. setting is flashing Setting the Tape Management FunctionTape Management Function @@@@TAPE@MANAGEMENT@@@@@@PRESS@EJECT Tape Management Conflict DisplayConflict display sample Pause/Still indicator N blinks Recording Speed ModeNormal Recording Normal Recording Before startingAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onClog Detection Recording CheckRepeat indicator will light Setting the Mode at the End of the TapeAutorepeat Recording Autorepeat RecordingAlarm Recording Setting Alarm RecordingAlarm Recording Counter Display Alarm RecordingConnections to the Alarm IN/OUT Terminals Alarm Reset in terminalAlarm Scan Alarm SearchRecording will not take place Program Timer RecordingDay of the week of the 8th line is flashing Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Repeat REC switch Series Recording SetupSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Single Image Recording Single Image Recording SetupAlarm trigger while in single image recording mode Normal Playback Special Playback Day/Time Search Special PlaybackShuttle Ring Operation D Search 01 0000 will be displayed on screenCounter will be reset to 0H 00M 00S Setting the Security LockTape Counter Is displayed on the digital displaySetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Data Transfer Speed Setup Setting the RS-232C or RS-485 Data Transfer SpeedDIP Switches Setup RS485 RJ-11 connector layout Setting the RS-232C or RS-485 Data Transfer SpeedConnector a Connector B Signal RS-485 ConnectionTape END OUT Terminal Output Setting Timer OUT TerminalOutput Terminals Tape END OUT TerminalSW OUT Terminal Output Setting Series OUT/NON REC OUT terminal settingField or Frame setting is flashing Output TerminalsRemote Jack Remote control settingSwitching heads combination and azimuth display Heads Switching FunctionMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRC4Q/U
Top Page Image Contents