Sanyo TLS-9960 instruction manual Autorepeat Recording, Setting the Mode at the End of the Tape

Page 20

AUTOREPEAT RECORDING

Autorepeat Recording

The same tape can be recorded over many times.

œFollow the Before starting steps, under “NORMAL RECORDING”.

1Set the REPEAT REC switch to the “ON” position.

øThe REPEAT indicator will light.

2Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@R1 öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

3Turn the JOG dial, until the “TAPE END MODE” setting is flashing.

4Turn the SHUTTLE ring to set to “R 1” or “R 2”. (See “Setting the Mode at the End of the Tape”)

5Press the SEARCH/AUDIO ON button to save the setting.

6Press the REC/PLAY SPEED l (or j) button to set the recording speed mode.

7Press the REC button.

øRecording will start. When the tape end is reached, the VCR will rewind it to the beginning, and recording will resume.

øWhen the end of the tape is reached, a buzzer will be heard (if in the (SETUP 2) menu, in the BUZZER section TAPE END is set to “Y”) and “OFF” will be displayed until the rewinding operation starts.

NOTES:

œIf during autorepeat recording there is an alarm trigger, “AL” is displayed on the digital display and alarm recording will take place. (Please refer to page 20, “ALARM RECORDING”.)

œIf the “TAPE END MODE” setting is R 1, the REPEAT indicator will go off if there is an alarm trigger. The recording will continue to the end of the tape then it will be rewound to the beginning and stop. “OFF” will be displayed on the digital display. To turn off the buzzer (if in the (SETUP 2) menu, in the BUZZER section TAPE END is set to “Y”) and the “OFF” display, press the STOP, EJECT or PLAY button, or turn the SHUTTLE ring.

œIf “AL” is displayed on the digital display and the “TAPE END MODE” setting is R1, autorepeat recording is not possible.

Setting the Mode at the End of the Tape

In the (SET UP 3) menu, you can set the mode of the VCR mode when the tape reaches the end during recording.

1Press the MENU button until the (SET UP 3) menu is displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@DURATION@@@20S

öEXT@TIME@ADJ.@@@@01:00

öTAPE@IN@MODE@@@@@STOP

öTAPE@END@MODE@@@@REW öTAPE@END@OUT@@@@@-3M öCLOG@DETECT.@@@@@Y öSERIES@REC@IN@@@@N öRS-232C@@@@@@@@@@19200

2Turn the JOG dial, until the “TAPE END MODE” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

œSetting when the REPEAT REC switch is set to the “OFF” position.

REW. . . . . . . Rewinds the tape to the beginning, then goes to stop mode

STOP . . . . . . Goes to stop mode EJECT . . . . . The cassette is ejected

œSetting when the REPEAT REC switch is set to the “ON” position.

R1 . . . . . . . . Autorepeat recording mode is automatically canceled if there was an alarm trigger

R2 . . . . . . . . Autorepeat recording mode is active even if there was an alarm trigger

4Press the SEARCH/AUDIO ON button to save the setting.

English

19

Page 19 Page 21
Image 20
Page 19 Page 21
Contents
TLS-9960 Precautions Contents FeaturesAccessory Front Panel Locations of Controls and Indicators Operation IndicatorsOperation Mode Indicator OFF indicatorBack Panel RS485 BConnections Power Cord InstallationAbout the memory reset Types of ON-SCREEN Displays and Display Sequence Reference pages are shown in square bracketsUsing the JOG dial and Shuttle ring Types of ON-SCREEN Displays and Display SequenceJOG dial Shuttle ringSetting the Language and Clock Setting procedure is now completedDay of week is set automatically Last 2 digits only are displayedChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Setting the Action to Take When a Cassette is Loaded Video Cassette TapesCorrect tape thread check function @@TIMING@@@@@@@@FIELDTape Management Function OperationIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape MANAGE. setting is flashingTape Management Function @@@@TAPE@MANAGEMENT @@@@@@PRESS@EJECT Tape Management Conflict Display Conflict display sample Recording Speed Mode Pause/Still indicator N blinksNormal Recording Normal Recording Before startingChanges to the Recording Speed Mode During Recording Action to Take when the Video Signal DeterioratesNormal Recording Concerning the Number of Times Tapes can be Rerecorded onRecording Check Clog DetectionSetting the Mode at the End of the Tape Repeat indicator will lightAutorepeat Recording Autorepeat RecordingAlarm Recording Alarm Recording SettingAlarm Recording Alarm Recording Counter DisplayConnections to the Alarm IN/OUT Terminals Alarm Reset in terminalAlarm Search Alarm ScanProgram Timer Recording Recording will not take placeProgram Timer Recording Day of the week of the 8th line is flashingSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Setup Repeat REC switchSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Single Image Recording Single Image Recording SetupAlarm trigger while in single image recording mode Normal Playback Special Playback Special Playback Day/Time SearchShuttle Ring Operation D Search 01 0000 will be displayed on screenSetting the Security Lock Counter will be reset to 0H 00M 00STape Counter Is displayed on the digital displaySetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Data Transfer Speed Setup Setting the RS-232C or RS-485 Data Transfer SpeedDIP Switches Setup Setting the RS-232C or RS-485 Data Transfer Speed RS485 RJ-11 connector layoutConnector a Connector B Signal RS-485 ConnectionTimer OUT Terminal Tape END OUT Terminal Output SettingOutput Terminals Tape END OUT TerminalSeries OUT/NON REC OUT terminal setting SW OUT Terminal Output SettingField or Frame setting is flashing Output TerminalsRemote control setting Remote JackHeads Switching Function Switching heads combination and azimuth displayMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRC4Q/U
Top Page Image Contents