Sanyo TLS-9960 instruction manual Remote Jack, Remote control setting

Page 41

OUTPUT TERMINALS

REMOTE Jack

You can use a VA-RMN01 Remote Control Unit (sold separately) to control remotely the VCR.

NOTE:

œThe functions not available on the VCR will not operate.

Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below, to the REMOTE jack.

NOTES:

œUse a 3.5 mm mini-jack type plug.

œThe connection should be done using a shielded cable no more than 5 meters long.

œThe functions not available on the VCR will not operate.

Remote control circuit

Remote control setting

The remote control switch 7 can be set to either eject the tape or access the menus.

1Press the MENU button until the (SET UP 1) menu is displayed.

@@@@@@@<SET@UP@1>

öDAYLIGHT@SET@@@@@USE

@@@@@@@@WEEK@MONTH@TIME

@ON@@@1ST-SUN@@04@02:00 @OFF@@LST-SUN@@10@02:00 öOUTPUT@@@@@@@@SERIES öCLOCK@SET @10-15-99@FRI@@15:20:00 öREMOTE@@@@@@@@EJECT öLANGUAGE-LANGUE-IDIOMA

@@@ENGLISH

2Turn the JOG dial, until the “REMOTE” setting is flashing.

3Turn the SHUTTLE ring, to select the desired switch mode.

EJECT . . . . . Switch 7 will eject the tape.

MENU. . . . . . Switch 7 will display the menu.

R0 1.2K

R1 0.3K

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

The resistance tolerance is 2% or less.

SW0: EJECT

SW1: STOP

SW2: STILL/PAUSE

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: EJECT (or MENU)

SW8: REV

SW9: REC/PLAY SPEED j, j

SW10: REC/PLAY SPEED l, l

SW11: SHIFT ], »

SW12: SHIFT «, «

4Press the SEARCH/AUDIO ON button to save the setting.

40

English

Page 40 Page 42
Image 41
Page 40 Page 42
Contents
TLS-9960 Precautions Contents FeaturesAccessory Front Panel Operation Indicators Locations of Controls and IndicatorsOperation Mode Indicator OFF indicatorRS485 B Back PanelConnections Power Cord InstallationAbout the memory reset Reference pages are shown in square brackets Types of ON-SCREEN Displays and Display SequenceTypes of ON-SCREEN Displays and Display Sequence Using the JOG dial and Shuttle ringJOG dial Shuttle ringSetting procedure is now completed Setting the Language and ClockDay of week is set automatically Last 2 digits only are displayedSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Date and time are displayedVideo Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedCorrect tape thread check function @@TIMING@@@@@@@@FIELDOperation Tape Management FunctionIf no tape management data is present on the tape If tape management data is present on the tapeTape MANAGE. setting is flashing Setting the Tape Management FunctionTape Management Function @@@@TAPE@MANAGEMENT@@@@@@PRESS@EJECT Tape Management Conflict DisplayConflict display sample Pause/Still indicator N blinks Recording Speed ModeNormal Recording Normal Recording Before startingAction to Take when the Video Signal Deteriorates Changes to the Recording Speed Mode During RecordingNormal Recording Concerning the Number of Times Tapes can be Rerecorded onClog Detection Recording CheckRepeat indicator will light Setting the Mode at the End of the TapeAutorepeat Recording Autorepeat RecordingAlarm Recording Setting Alarm RecordingAlarm Recording Counter Display Alarm RecordingConnections to the Alarm IN/OUT Terminals Alarm Reset in terminalAlarm Scan Alarm SearchRecording will not take place Program Timer RecordingDay of the week of the 8th line is flashing Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Repeat REC switch Series Recording SetupSeries Recording Series recording connectionsLoop recording connection example with 2 VCRs Continous Loop Recording SetupSeries Recording Single Image Recording Single Image Recording SetupAlarm trigger while in single image recording mode Normal Playback Special Playback Day/Time Search Special PlaybackShuttle Ring Operation D Search 01 0000 will be displayed on screenCounter will be reset to 0H 00M 00S Setting the Security LockTape Counter Is displayed on the digital displaySetting procedure on the first VCR is now completed Setting the BuzzerClock Adjustment Data Transfer Speed Setup Setting the RS-232C or RS-485 Data Transfer Speed DIP Switches Setup RS485 RJ-11 connector layout Setting the RS-232C or RS-485 Data Transfer SpeedConnector a Connector B Signal RS-485 ConnectionTape END OUT Terminal Output Setting Timer OUT TerminalOutput Terminals Tape END OUT TerminalSW OUT Terminal Output Setting Series OUT/NON REC OUT terminal settingField or Frame setting is flashing Output TerminalsRemote Jack Remote control settingSwitching heads combination and azimuth display Heads Switching FunctionMaintenance Maintaining and Checking The Mechanism MaintenanceMaintenance Table System Down Troubleshooting GuideAfter a Power Failure Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRC4Q/U
Top Page Image Contents