Sanyo TLS-9960 Normal Recording, Concerning the Number of Times Tapes can be Rerecorded on

Page 18

NORMAL RECORDING

Concerning the Number of Times Tapes can be Rerecorded on

Depending on the recording speed mode, the tape must be replaced after a certain number of recording times.

Refer to the table below for the maximum number of times a tape can be recorded on.

Recording speed mode

Maximum number of

(hour mode)

recording times

 

 

(with a standard grade

 

 

tape)

2

 

100

 

 

 

12,

24

50

 

 

48

25

 

 

72

15

 

 

96, 120

10

 

 

 

168,

240

5

 

 

360

3

 

 

480

2

 

 

 

720,

960

1

 

 

1 SHOT

1

 

 

 

Changes to the Recording Speed Mode During Recording

It is possible to permit or prevent changing the recording speed mode during recording.

1Press the MENU button until the (SET UP 4) menu is displayed.

@@@@@@@@<SET@UP@4>

öSW@OUT

@@FIELD@@@@@@@@@01

@@TIMING@@@@@@@@FIELD

@@2H@@@@@@@@@@@@Y

öTHREAD@CHECK@@@Y

öVIDEO@LOSS@@@@@N

öREC@SPEED@@@@@@N

ö1@SHOT@SET

@@FIELD@@@@@@@@@1

@@INTERVAL@@@@@@1M

2Turn the JOG dial, until the “REC SPEED” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

Y. . . . . . . . . . Recording speed mode can be changed

N. . . . . . . . . Recording speed mode can not be changed

4Press the SEARCH/AUDIO ON button to save the setting.

NOTES:

œThe maximum number of recording times will vary depending on the location and kind of tape used. Verify the recording quality and replace the tape when the quality starts to deteriorate.

The maximum number of recording times indicated above are based on test tapes (T-120) used by the company.

œIf using longer tapes (i.e. T-160) the tape travel will not be as stable and that may cause problems.

Action to Take when the Video Signal Deteriorates

If there is no video signal during recording, fast forward, rewind modes, when in stop mode or when a tape is not loaded the menus are not displayed, “VIDEO LOSS” can be displayed on-screen and a signal (0 V) can be output at the ALARM OUT terminal. If in the (SET UP 2) menu, in the BUZZER section WARNING is set to “Y”, the buzzer will be heard. To stop the buzzer, press the STOP button.

1Press the MENU button until the (SET UP 4) menu is displayed.

2Turn the JOG dial, until the “VIDEO LOSS” setting is flashing.

3Turn the SHUTTLE ring, to set the desired mode.

N. . . . . . . . . The video loss warning is not active.

Y. . . . . . . . . . The video loss warning is active.

4Press the SEARCH/AUDIO ON button to save the setting.

English

17

Page 17 Page 19
Image 18
Page 17 Page 19
Contents
TLS-9960 Precautions Features AccessoryContents Front Panel Operation Mode Indicator Locations of Controls and IndicatorsOperation Indicators OFF indicatorBack Panel RS485 BPower Cord Installation About the memory resetConnections Types of ON-SCREEN Displays and Display Sequence Reference pages are shown in square bracketsJOG dial Using the JOG dial and Shuttle ringTypes of ON-SCREEN Displays and Display Sequence Shuttle ringDay of week is set automatically Setting the Language and ClockSetting procedure is now completed Last 2 digits only are displayedChanging the Date/Time Display Position Changing the ON-SCREEN DisplaySelecting the On-screen Display Date and time are displayedVideo Cassette Tapes Correct tape thread check function Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes @@TIMING@@@@@@@@FIELD If no tape management data is present on the tape Tape Management Function Operation If tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionTape MANAGE. setting is flashing @@@@TAPE@MANAGEMENTTape Management Conflict Display Conflict display sample@@@@@@PRESS@EJECT Normal Recording Recording Speed ModePause/Still indicator N blinks Normal Recording Before startingNormal Recording Changes to the Recording Speed Mode During RecordingAction to Take when the Video Signal Deteriorates Concerning the Number of Times Tapes can be Rerecorded onRecording Check Clog DetectionAutorepeat Recording Setting the Mode at the End of the TapeRepeat indicator will light Autorepeat RecordingAlarm Recording Alarm Recording SettingConnections to the Alarm IN/OUT Terminals Alarm RecordingAlarm Recording Counter Display Alarm Reset in terminalAlarm Search Alarm ScanProgram Timer Recording Recording will not take placeProgram Timer Recording Day of the week of the 8th line is flashingTo Cancel a Program Timer Recording Setting the HolidaysChanging a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Series Recording Series Recording SetupRepeat REC switch Series recording connectionsContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Single Image Recording Setup Alarm trigger while in single image recording modeSingle Image Recording Normal Playback Special Playback Shuttle Ring Operation Special PlaybackDay/Time Search D Search 01 0000 will be displayed on screenTape Counter Setting the Security LockCounter will be reset to 0H 00M 00S Is displayed on the digital displaySetting the Buzzer Clock AdjustmentSetting procedure on the first VCR is now completed Setting the RS-232C or RS-485 Data Transfer Speed DIP Switches SetupData Transfer Speed Setup Connector a Connector B Signal Setting the RS-232C or RS-485 Data Transfer SpeedRS485 RJ-11 connector layout RS-485 ConnectionOutput Terminals Timer OUT TerminalTape END OUT Terminal Output Setting Tape END OUT TerminalField or Frame setting is flashing Series OUT/NON REC OUT terminal settingSW OUT Terminal Output Setting Output TerminalsRemote control setting Remote JackHeads Switching Function Switching heads combination and azimuth displayMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRC4Q/U
Top Page Image Contents