2INSTALL BATTERIES
•Install two “AAA” Batteries (not included) so that the “+” and
To review the remote control functions, go to pages 14~15.
3CONNECT AC POWER CORD
•Connect AC Power Cord (supplied) to the Plasma TV and electrical outlet as shown here.
The AC outlet must be near this equipment and must be easily accessible.
IMPORTANT NOTE: Spent or dis- charged batteries must be recycled or disposed of properly in compliance with all applicable laws. For detailed information, contact your local County Solid Waste Authority.
To POWER CORD
CONNECTOR on back
of Plasma TV.
To 120 V AC outlet.
4CHANNEL SEARCH (REQUIRED SET-UP)
When the television is powered on for the first time,
it automatically checks for the presence of Digital and |
|
|
|
|
|
|
|
|
|
|
|
|
| First |
|
| ||||||
INPUT |
| POWER |
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
| ||||||||||||||
Analog RF signals. |
|
|
|
|
|
| 1 |
|
|
|
|
|
| Please connect all signals |
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| 2 |
|
|
| 3 |
|
| and antennas to jacks and |
|
| |
|
|
|
|
|
| 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 |
|
|
|
|
|
|
| the terminals on the back. |
|
| ||||
• Press the POWER key to turn on the TV. |
|
|
|
| 7 |
|
|
|
|
|
|
|
|
|
| 6 |
|
|
| Then press CHannel UP key. ➠ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| INFO | 0 | 8 |
|
| SLEEP |
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| 9 |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Analog Antenna 34 |
| |
• Then press the CHANNEL UP key to automati- |
|
|
| RECALL |
|
| TUNER |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| MUTE |
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
| ENTER |
|
|
|
|
|
| |||||
|
|
| MENU |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
cally search for available channels: Digital |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 |
|
|
| |
(ATSC) and Analog (NTSC). |
|
|
|
|
|
|
|
|
|
|
|
|
|
| AUTO DATE AND TIME SETTING | |||||||
CAPTION |
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
If an analog channel was found, the TV will |
|
|
|
|
|
|
|
| EXIT |
|
|
|
|
|
|
|
|
| ||||
CH |
|
|
|
|
|
|
|
|
|
|
| (OPTIONAL) |
|
| ||||||||
start Auto Clock Setting (see step 5). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| VOL |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
NOTES: Channel information found during channel search is stored in two Channel Scan Memory databases (Analog and Digital). After channel search is completed, the TV will tune to the lowest Digital channel or lowest Analog channel if no digital channels are found.
If the TV does not detect any digital or analog channels, a message advising the viewer to check the cables and antenna connections will appear. In this case, you must press the CHANNEL UP key again to repeat the channel search process. If after two searches the TV still fails to detect any channels, the TV will tune to analog channel 3. These two channel searches are required even if you plan to use the TV only as a monitor.
If no analog or digital channels are found after the second search, Channel Search will default to
If an analog channel was found during channel search, the TV will begin Auto Date and Time setting. This feature searches for a local PBS station that is broadcasting Date and Time data. These data are used to automatically set the date and time. (This may take several seconds.)
After the Date and Time are set, the lowest Digital channel (or lowest Analog channel if no active digital channel is stored in the Channel Scan Memory) will be tuned.
To cancel auto Date and Time setting, press the CHANNEL UP key. To set the Date and Time manually, see page 24.
6ANTENNA SELECTION (OPTIONAL)
To change the initial analog tuning system setup (from antenna to cable or cable to antenna), use the
8