Sanyo DTL-4800 instruction manual Trigger Shot Recording, Connections Using a Multiplexer

Page 37

TRIGGER SHOT RECORDING

When the trigger shot recording function is set, the set number of frames will be recorded when there is an input at the TRIGGER SHOT REC IN terminal.

Connections Using a Multiplexer

Video camera	Monitor TV

Trigger Shot Recording Setup

1 In stop mode, press the REC/PLAY SPEED l (or j)

button, to set the recording speed to “000”.

2 Press the MENU button to display the (MAIN MENU

1) menu.

3 Press the SHIFT ] button to select the “6. RECORD

Video camera

Video camera

Video camera

VIDEO output jack

SET” line, then press the MENU button.

øThe (RECORD SET) menu appears.

@@@@@<RECORD@SET>

*ALARM@RECORD@MODE@@Y1

@@SPEED@@@@@@@@@@@@@N12

@@DURATION@@@@@@@@@@20S

*PRE@ALARM@RECORD@@@OFF

*POST@ALARM@RECORD@@OFF

@@DURATION@@@@@@@@@@20S

*TRIGGER@SHOT@REC@@@1

*TAPE@END@MODE@@@@@@REW

Multiplexer

SW IN terminal

SW OUT terminal	VIDEO IN
	jack

TRIGGER SHOT REC IN terminal

4Press the SHIFT ] (or \) button until the “TRIGGER SHOT REC” setting is flashing.

5Press the DATA l (or j) button to set the number of frames to record (1, 4, 9 or 16).

6Press the MENU EXIT button to save the settings.

7Press the REC button.

øThe trigger shot recording mode will be activated (the VCR will be in recording stand-by mode).

8When there is an input (trigger) at the TRIGGER SHOT REC IN terminal on the back panel trigger shot recording is done.

NOTES:

œTrigger shot recording can only be conducted in F12-hour recording mode.

œThe trigger at the TRIGGER SHOT REC IN terminal should be on for 0.1 sec. or more.

œWhen using the TRIGGER SHOT REC IN terminal, connect a make-contact switch (no voltage) between the TRIGGER SHOT REC IN and COM terminals.

œWhen a setup using a multiplexer or quad compressor is used, if the number of frames set at step 5 is the same as the number of cameras, when there is an input at the TRIGGER SHOT REC IN terminal one frame from each camera will be recorded.

œFor detailed instructions, please refer to the multiplexer or quad compressor instruction manual.

36

English

Image 37

Contents Digital For the customers in Canada PrecautionsDeclaration of Conformity Precautions Features ContentsAccessories Front Panel Locations of Controls and IndicatorsSTILL/PAUSE button Search FRAME/FIELD button Eject button Menu Exit buttonOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator Digital DisplayOFF indicator Male on the VCR Back PanelO P Q R S T Protection against power failure Installing the Ni-Cd BatteryConnections About the memory reset Power Cord InstallationConnections Main menus ON-SCREEN MenusSub-menus ON-SCREEN Menus Language Setting Setting the Language and ClockClock Setting Day of week is set automaticallyAutomatic Daylight Saving Time Adjustment Setting the Language and ClockSelecting the On-screen Display Changing the ON-SCREEN DisplayChanging the Date/Time Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is LoadedCorrect tape thread check function Various SET 1 menu appearsOperation Tape Management FunctionIf no tape management data is present on the tape If tape management data is present on the tapeTape Management Function Setting the Tape Management FunctionTape Management menu appears Conflict display sample Tape Management Conflict DisplayPause/Still indicator N blinks Recording speed mode is displayed on the digital displayNormal Recording Normal Recording Before startingNormal Recording Recording Speed ModeField HourRecording Check Concerning the Number of Times Tapes can be Rerecorded onClog Detection Action to Take when the Video Signal Deteriorates Setting the Mode at the End of the TapeRecord SET menu appears Setup for use with a multiplexer Changes to the Recording Speed Mode During RecordingAutorepeat Recording Repeat indicator will lightAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Recording Counter Display Alarm RecordingConnections to the Alarm IN/OUT Terminals Alarm Reset in terminalAlarm Scan Alarm SearchPost Alarm Recording Setting Pre Alarm Recording SettingRecording speed mode Recording duration Seconds Program Timer Recording Press the Data l or j button to select Y Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Trigger Shot Recording Setup Connections Using a MultiplexerTrigger Shot Recording Recording will start in series recording mode Series Recording SetupSeries Recording Series recording connectionsSeries Recording Continous Loop Recording SetupLoop recording connection example with 2 VCRs Playback Playback Tape CounterSearch Forward and Reverse Field Advance Forward and ReverseDay/Time Search DAY/TIME SearchD Search 01 000000 will be displayed on screen Setting the Security Lock Setting the Security LockCancel the Security Lock Setting and Canceling the Quick Method Security LockIf using the SET UP setting, continue with steps 4 Setting the BuzzerBuzzer SET menu appears Setting procedure on the first VCR is now completed Clock AdjustmentCassette Eject Setup Setting the Cassette Eject ModeEject terminal connection Eject in terminalDIP Switches Setup Setup for RS-232C or RS-485 USESW No ExampleSetup for RS-232C or RS-485 Use Setup for RS-232C or RS-485 USERS-485 RJ-11 connector layout RS-485 ConnectionPin Signal Operation Signal direction RS-232C 9-pin connector layoutPOWER/DEW/USED Time menu appears Output Terminals Timer OUT TerminalTape END OUT Terminal COM TerminalOutput Terminals Remote control settingRemote Jack NON REC OUT terminalMaintenance Maintenance Table MaintenanceMaintaining and Checking The Mechanism After a Power Failure Troubleshooting GuideSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRD2QD/NA

Related manuals

Manual 57 pages 41.55 Kb