Sanyo DTL-4800 instruction manual Tape Management Conflict Display, Conflict display sample

Page 21

TAPE MANAGEMENT FUNCTION

Tape Management Conflict Display

If when the tape management function checks the tape data a conflict that prevents recording is found, the (TAPE MANAGEMENT) menu is displayed with the conflicting setting flashing and the VCR go into stop mode. If in the (BUZZER SET) menu, WARNING is set to “Y”, the buzzer is heard. (To stop the buzzer, press the STOP button.)

NOTES:

œIf “OVERRIDE” is set to “N” (No), the conflicting setting is displayed flashing and the message (PRESS EJECT) is displayed at the bottom of the screen. Recording under these conditions is not possible. Press the EJECT button to eject the tape. To record on the same tape, set the OVERRIDE setting to “Y” and modify the conflicting setting, then insert the same tape and press the REC button. However, if only “PROTECT DAY” and “REC PASS SET” are modified, the menu will be displayed again. Press the REC button one more time to start recording. Recording starts and the tape data is updated.

Conflict display sample

@@@<TAPE@MANAGEMENT>

*TAPE@MANAGE.@@@@N

*PROTECT@DAY@@@@@30

@LAST@M/D@@@@@@NEXT@M/D

@@@@@12/15@@@@@@@@@@1/16

*REC@PASS@SET@@@@10

@PASS@COUNT@@@@@@10

*GROUP@NO.@@@@@@@7

@REC@GR.NO.@@@@@@8

*OVERRIDE@@@@@@@@N

@@@@@@(PRESS@EJECT)

œIf the “OVERRIDE” is set to “Y” (Yes), the (TAPE MANAGEMENT) menu is displayed and conflicting setting preventing recording will flash and VCR go into the stop mode.

To enter the record mode, press the REC button.

PROTECT DAY CONFLICT

The tape is protected, the tape protection term (ex. 30 days) is not yet over.

Under LAST M/D, the date of the last recording on the tape (or the last expected recording date (calculated using the tape length (ST-180XZES) and the recording speed)) is displayed.

Under NEXT M/D, the date when it will be possible to record on the tape again is displayed.

REC PASS SET CONFLICT

The set number of recording passes has been reached.

The PASS COUNT shows the number of recording passes on the tape (ex. since the maximum number of recording passes is set to “10”, this prevents further recording.)

NOTES:

œWhen conducting Autorepeat recording, if the PASS COUNT exceeds 100, “101*” will be displayed flashing.

œIf using a tape recorded previously on a different type of VCR (no tape data), when the set number of recordings is exceeded, “USED” will flash next to the PASS COUNT number.

GROUP NO. CONFLICT

The group numbers do not match.

The REC GR. NO. shows the tape recording group number (ex. this tape belongs to a different recording group number 8 than the one set 7.)

20

English

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Digital Precautions For the customers in CanadaDeclaration of Conformity Precautions Contents FeaturesAccessories Front Panel Locations of Controls and IndicatorsSTILL/PAUSE button Search FRAME/FIELD button Eject button Menu Exit buttonOperation Indicators Locations of Controls and IndicatorsOperation Mode Indicator Digital DisplayOFF indicator Male on the VCR Back PanelO P Q R S T Installing the Ni-Cd Battery Protection against power failureConnections Power Cord Installation About the memory resetConnections ON-SCREEN Menus Main menusSub-menus ON-SCREEN Menus Language Setting Setting the Language and ClockClock Setting Day of week is set automaticallyAutomatic Daylight Saving Time Adjustment Setting the Language and ClockChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Video Cassette Tapes Video Cassette Tapes Setting the Action to Take When a Cassette is Loaded Correct tape thread check function Various SET 1 menu appearsOperation Tape Management FunctionIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management menu appears Conflict display sample Tape Management Conflict DisplayPause/Still indicator N blinks Recording speed mode is displayed on the digital displayNormal Recording Normal Recording Before startingNormal Recording Recording Speed ModeField HourConcerning the Number of Times Tapes can be Rerecorded on Recording CheckClog Detection Setting the Mode at the End of the Tape Action to Take when the Video Signal DeterioratesRecord SET menu appears Setup for use with a multiplexer Changes to the Recording Speed Mode During RecordingRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Recording Counter Display Alarm RecordingConnections to the Alarm IN/OUT Terminals Alarm Reset in terminalAlarm Scan Alarm SearchPre Alarm Recording Setting Post Alarm Recording SettingRecording speed mode Recording duration Seconds Program Timer Recording Press the Data l or j button to select Y Program Timer RecordingChanging a Program Timer Recording Setting the HolidaysTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Connections Using a Multiplexer Trigger Shot Recording SetupTrigger Shot Recording Recording will start in series recording mode Series Recording SetupSeries Recording Series recording connectionsContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Playback Playback Tape CounterSearch Forward and Reverse Field Advance Forward and ReverseDAY/TIME Search Day/Time SearchD Search 01 000000 will be displayed on screen Setting the Security Lock Setting the Security LockCancel the Security Lock Setting and Canceling the Quick Method Security LockSetting the Buzzer If using the SET UP setting, continue with steps 4Buzzer SET menu appears Setting procedure on the first VCR is now completed Clock AdjustmentCassette Eject Setup Setting the Cassette Eject ModeEject terminal connection Eject in terminalDIP Switches Setup Setup for RS-232C or RS-485 USESW No ExampleSetup for RS-232C or RS-485 Use Setup for RS-232C or RS-485 USERS-485 RJ-11 connector layout RS-485 ConnectionRS-232C 9-pin connector layout Pin Signal Operation Signal directionPOWER/DEW/USED Time menu appears Output Terminals Timer OUT TerminalTape END OUT Terminal COM TerminalOutput Terminals Remote control settingRemote Jack NON REC OUT terminalMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRD2QD/NA
Related manuals
Manual 57 pages 41.55 Kb
Top Page Image Contents