Sanyo DTL-4800 Setup for RS-232C or RS-485 USE, Setup for RS-232C or RS-485 Use, Types of cables

Page 48

SETUP FOR RS-232C OR RS-485 USE

Setup for RS-232C or RS-485 Use

1Press the MENU button to display the (MAIN MENU 1) menu.

2Press the SHIFT ] (or \) button until the (MAIN MENU 2) menu is displayed.

3Press the SHIFT ] (or \) button to select the “1. RS-485 SET (or RS-232C SET)” line, then press the MENU button.

øThe (RS-485 SET (or RS-232C SET)) menu appears.

@@@<RS-485@SET> @DATA@SPEED@@@@@19200 @STATUS@INFO@@@@Y @ALARM@INFO@@@@@Y

øThe menu name will depend on the DIP switch 9 setting. When down (RS-232C SET) is displayed and when up (RS-485 SET) is displayed.

øThe STATUS INFO and ALARM INFO lines are only displayed when DIP switch 9 is set to 485.

4Press the DATA l (or j) button to set the desired transfer speed.

192002400 48009600

5Press the SHIFT ] button, until the “STATUS INFO” setting is flashing.

6Press the DATA l (or j) button to set the desired setting.

Y. . . . . . . . . The VCR status information (state information and warning state) and mode changes are output at the RS-485 connector.

N. . . . . . . . . The VCR status information (state information and warning state) and mode changes are not output at the RS-485 connector.

7Press the SHIFT ] button, until the “ALARM INFO” setting is flashing.

8Press the DATA l (or j) button to set the desired setting.

Y. . . . . . . . . . The VCR alarm information (alarm recording start and stop) and video loss information are output at the RS-485 connector.

N. . . . . . . . . The VCR alarm information (alarm recording start and stop) and video loss information are not output at the RS-485 connector.

9Press the MENU EXIT button to save the setting.

RS-485 RJ-11 connector layout

 

1

6

 

NOTE: Do not connect to phone line.

 

 

 

 

Pin number

Connector A

Connector B

signal

signal

 

1

Not used

Not used

 

 

 

2

Not used

Not used

 

 

 

 

3

 

A

B

 

 

 

 

4

 

B

A

 

 

 

5

Not used

Not used

 

 

 

6

Not used

Not used

 

 

 

 

A:Non-inverting driver output/receiver input

B:Inverting driver output/receiver input

RS-485 Connection

This VCR can use the straight type or crossed type connecting cables.

If using a straight type cable, connect it from the “A” to the “A” or from the “B” to the “B” RS-485 connector.

If using a crossed type cable, connect it from the “A” to the “B” or from the “B” to the “A” RS-485 connector.

Types of cables

Straight type: A cable with pin connection number correspondence (e.g. pin 1 to pin 1, pin 2 to pin 2, etc.).

Crossed type: A cable without pin connection number correspondence.

English

47

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Digital Precautions For the customers in CanadaDeclaration of Conformity Precautions Contents FeaturesAccessories Locations of Controls and Indicators Front PanelSTILL/PAUSE button Search FRAME/FIELD button Eject button Menu Exit buttonLocations of Controls and Indicators Operation IndicatorsOperation Mode Indicator Digital DisplayOFF indicator Back Panel Male on the VCRO P Q R S T Installing the Ni-Cd Battery Protection against power failureConnections Power Cord Installation About the memory resetConnections ON-SCREEN Menus Main menusSub-menus ON-SCREEN Menus Setting the Language and Clock Language SettingClock Setting Day of week is set automaticallySetting the Language and Clock Automatic Daylight Saving Time AdjustmentChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Video Cassette Tapes Setting the Action to Take When a Cassette is Loaded Video Cassette TapesCorrect tape thread check function Various SET 1 menu appearsTape Management Function OperationIf no tape management data is present on the tape If tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management menu appears Tape Management Conflict Display Conflict display sampleRecording speed mode is displayed on the digital display Pause/Still indicator N blinksNormal Recording Normal Recording Before startingRecording Speed Mode Normal RecordingField HourConcerning the Number of Times Tapes can be Rerecorded on Recording CheckClog Detection Setting the Mode at the End of the Tape Action to Take when the Video Signal DeterioratesRecord SET menu appears Changes to the Recording Speed Mode During Recording Setup for use with a multiplexerRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Alarm Recording SettingAlarm Recording Alarm Recording Counter DisplayConnections to the Alarm IN/OUT Terminals Alarm Reset in terminalAlarm Search Alarm ScanPre Alarm Recording Setting Post Alarm Recording SettingRecording speed mode Recording duration Seconds Program Timer Recording Program Timer Recording Press the Data l or j button to select YSetting the Holidays Changing a Program Timer RecordingTo Cancel a Program Timer Recording To Cancel all Program Timer RecordingsThese portions will not be recorded Recording Using AN External Timer Input Connections Using a Multiplexer Trigger Shot Recording SetupTrigger Shot Recording Series Recording Setup Recording will start in series recording modeSeries Recording Series recording connectionsContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Playback Tape Counter PlaybackSearch Forward and Reverse Field Advance Forward and ReverseDAY/TIME Search Day/Time SearchD Search 01 000000 will be displayed on screen Setting the Security Lock Setting the Security LockCancel the Security Lock Setting and Canceling the Quick Method Security LockSetting the Buzzer If using the SET UP setting, continue with steps 4Buzzer SET menu appears Clock Adjustment Setting procedure on the first VCR is now completedSetting the Cassette Eject Mode Cassette Eject SetupEject terminal connection Eject in terminalSetup for RS-232C or RS-485 USE DIP Switches SetupSW No ExampleSetup for RS-232C or RS-485 USE Setup for RS-232C or RS-485 UseRS-485 RJ-11 connector layout RS-485 ConnectionRS-232C 9-pin connector layout Pin Signal Operation Signal directionPOWER/DEW/USED Time menu appears Timer OUT Terminal Output TerminalsTape END OUT Terminal COM TerminalRemote control setting Output TerminalsRemote Jack NON REC OUT terminalMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Sanyo Industrial VCR Warranty Weekdays 830 AM 500 PM Pacific TimeRD2QD/NA
Related manuals
Manual 57 pages 41.55 Kb
Top Page Image Contents