Sanyo DTL-4800 Output Terminals, Remote Jack, Remote control setting, NON REC OUT terminal

Page 51

OUTPUT TERMINALS

REMOTE Jack

You can use a VA-RMN01 Remote Control Unit (sold separately) to control remotely the VCR.

NOTE:

œThe functions not available on the VCR will not operate.

Remote control of the VCR is possible by connecting a remote controller with a circuit such as indicated below, to the REMOTE jack.

NOTES:

œUse a 3.5 mm mini-jack type plug.

œThe connection should be done using a shielded cable no more than 5 meters long.

œThe functions not available on the VCR will not operate.

Remote control setting

The remote control switch 7 can be set to either eject the tape or access the menus.

1Press the MENU button to display the (MAIN MENU 1) menu.

2Press the SHIFT ] button to select the “4. VARIOUS SET 1” line, then press the MENU button.

øThe (VARIOUS SET 1) menu appears.

@@@@<VARIOUS@SET@1>

*THREAD@CHECK@@@@Y

*REMOTE@@@@@@@@@@EJECT

*EXT@TIME@ADJ.@@@01:00

*TAPE@END@OUT@@@@PRE

*EJECT@SET

@@EJECT@MODE@@@@@EJECT1

@@OPERATION@@@@@@SLAVE

3 Press the SHIFT ] button, until the “REMOTE”

setting is flashing.

Remote control circuit

R0 1.2K

R1 0.3K

R2 0.43K

R3 0.51K

R4 0.62K

R5 0.75K

R6 0.91K

R7 1.1K

R8 1.3K

R9 2.0K

R10 2.4K

R11 3.6K

R12 5.6K

The resistance tolerance is 2% or less.

SW0: EJECT

SW1: STOP

SW2: STILL/PAUSE

SW3: REW

SW4: FF

SW5: PLAY

SW6: REC

SW7: EJECT (or MENU)

SW8: Not used

SW9: REC/PLAY SPEED, DATA j

SW10: REC/PLAY SPEED, DATA l

SW11: SHIFT ]

SW12: SHIFT «

4 Press the DATA l (or j) button to select the desired

switch mode.

EJECT . . . . . Switch 7 will eject the tape.

MENU . . . . . Switch 7 will display the menu.

5Press the MENU EXIT button to save the setting.

NON REC OUT terminal

If during recording the VCR enters a mode other than recording (i.e. recording pause, stop mode, etc.), a LOW signal (0 V) is output. If recording is resumed, then a HIGH signal (5 V) is output.

If in the (BUZZER SET) menu, NON REC is set to “Y”, a buzzer will be heard while the VCR is in non recording mode. The buzzer will stop if the STOP button is pressed (the output signal will remain LOW (0 V)).

50

English

Image 51

Contents Digital Precautions For the customers in CanadaDeclaration of Conformity Precautions Contents FeaturesAccessories Search FRAME/FIELD button Eject button Menu Exit button Locations of Controls and IndicatorsFront Panel STILL/PAUSE buttonDigital Display Locations of Controls and IndicatorsOperation Indicators Operation Mode IndicatorOFF indicator Male on the VCR Back PanelO P Q R S T Installing the Ni-Cd Battery Protection against power failureConnections Power Cord Installation About the memory resetConnections ON-SCREEN Menus Main menusSub-menus ON-SCREEN Menus Day of week is set automatically Setting the Language and ClockLanguage Setting Clock SettingAutomatic Daylight Saving Time Adjustment Setting the Language and ClockChanging the ON-SCREEN Display Selecting the On-screen DisplayChanging the Date/Time Display Position Video Cassette Tapes Various SET 1 menu appears Setting the Action to Take When a Cassette is LoadedVideo Cassette Tapes Correct tape thread check functionIf tape management data is present on the tape Tape Management FunctionOperation If no tape management data is present on the tapeSetting the Tape Management Function Tape Management FunctionTape Management menu appears Conflict display sample Tape Management Conflict DisplayNormal Recording Before starting Recording speed mode is displayed on the digital displayPause/Still indicator N blinks Normal RecordingHour Recording Speed ModeNormal Recording FieldConcerning the Number of Times Tapes can be Rerecorded on Recording CheckClog Detection Setting the Mode at the End of the Tape Action to Take when the Video Signal DeterioratesRecord SET menu appears Setup for use with a multiplexer Changes to the Recording Speed Mode During RecordingRepeat indicator will light Autorepeat RecordingAutorepeat Recording Alarm Recording Setting Alarm RecordingAlarm Reset in terminal Alarm RecordingAlarm Recording Counter Display Connections to the Alarm IN/OUT TerminalsAlarm Scan Alarm SearchPre Alarm Recording Setting Post Alarm Recording SettingRecording speed mode Recording duration Seconds Program Timer Recording Press the Data l or j button to select Y Program Timer RecordingTo Cancel all Program Timer Recordings Setting the HolidaysChanging a Program Timer Recording To Cancel a Program Timer RecordingThese portions will not be recorded Recording Using AN External Timer Input Connections Using a Multiplexer Trigger Shot Recording SetupTrigger Shot Recording Series recording connections Series Recording SetupRecording will start in series recording mode Series RecordingContinous Loop Recording Setup Series RecordingLoop recording connection example with 2 VCRs Playback Field Advance Forward and Reverse Tape CounterPlayback Search Forward and ReverseDAY/TIME Search Day/Time SearchD Search 01 000000 will be displayed on screen Setting and Canceling the Quick Method Security Lock Setting the Security LockSetting the Security Lock Cancel the Security LockSetting the Buzzer If using the SET UP setting, continue with steps 4Buzzer SET menu appears Setting procedure on the first VCR is now completed Clock AdjustmentEject in terminal Setting the Cassette Eject ModeCassette Eject Setup Eject terminal connectionExample Setup for RS-232C or RS-485 USEDIP Switches Setup SW NoRS-485 Connection Setup for RS-232C or RS-485 USESetup for RS-232C or RS-485 Use RS-485 RJ-11 connector layoutRS-232C 9-pin connector layout Pin Signal Operation Signal directionPOWER/DEW/USED Time menu appears COM Terminal Timer OUT TerminalOutput Terminals Tape END OUT TerminalNON REC OUT terminal Remote control settingOutput Terminals Remote JackMaintenance Maintenance Maintenance TableMaintaining and Checking The Mechanism Troubleshooting Guide After a Power FailureSystem Down Specifications Weekdays 830 AM 500 PM Pacific Time Sanyo Industrial VCR WarrantyRD2QD/NA

Related manuals

Manual 57 pages 41.55 Kb