CHAPTER 8: Batch Operation
8.1 Receiving Batch Data from the SNA host
When SNA data is received from the host by the A/S-4, the data is sent to the VDU as follows:
| | | | Start | Special | End of | |
VDU | CMD | Device | On | of File | Control | File | VDU |
1.VDU CMD or CRT lead in character is selected by C-VDU commands menu. This single or dual character command is not sent to the VDU if the Device ON command is selected for a control character (X`1F’ or less) or disabled by being set to a space.
2.Device (Printer, Card, Disk) On is selected by C-VDU commands menu. This single or dual character command directs the received SNA data to the correct device; printer, card or disk. This command can also be disabled (turned off) by setting it to a space so that no Device On is sent. If the command is set to a printable character (X`21’ or greater) the VDU CMD will precede the Device On command.
NOTE
Console data is not preceded by a VDU CMD or a Device On character.
3.Start of File (SOF) character is selected by H- Application Options menu. This single character command can be disabled (turned off) so that no Start of File character is sent.
4.Special Control (SC) characters precede some types of data mentioned below:
a.SOH ($01) character indicates that a Function Management Header-2 follows. The FMH-2 data is sent to the VDU without converting the SNA EBCDIC data to ASCII (transparent mode) inserting DLE’s before ASCII control characters if needed. The VDU CMD and device selection are sent along with this message if selected.
Protocol Converter Model A/S-4
FCC Statement
Protocol Converter Model A/S-4
Trademarks
Contents
Contents
General Information
General Information
Specifications
Indicators Power
Modem Interface
Installation
1General Installation
Terminal Automatic Speed Detection
Power Transformer
Synchronizer
CLEAR-TO-SEND
Switches
Terminal Switches
Carrier Detect
REQUEST-TO-SEND
Baud Rate
How to Set Terminal Port Switches for Different Devices
Devices
Modem Switches
REQUEST-TO-SEND
How to Set Modem Port Switches for Different Devices
Option Switches
LED Indicator
Power Up and Configuration Menu Operations
Power Up
Power Up Message
Type Home for VDU Match or Space Version
A/S-4 Main Menu
Current
Protocol Converter Main Menu RUN no Changes Else Change VDU
Switching from A/S-4’s Main Menu to Running the Application
Protocol Converter Model A/S-4
Changing the VDU Type
Current
VDU = NEW VDU
Changing VDU Commands for the VDU Type Selected
Changing Video Attributes and Commands for VDU
ESC X Y Z
4 Standard Keyboard Layout
Power Up and Configuration Menu Options
ADM 1178 Keyboard Layout
IBM 3101 Keyboard Layout
PNS Keyboard Layout
Changing Keyboard Layout Type
Protocol Converter Model A/S-4
ESC or =PF20
PA Keys
CTL Z or
Protocol Converter Model A/S-4
Changing Application
Changing Application Options
Do not set the VDU and PRT LU addresses to the same values
XON/XOFF=OFF
Changing Batch Application Options
Printer Options
Current
Power Up and Configuration Menu Options
Programmable Printer Options
Verify Switch Settings
Reload Default Options
Interactive Operation
Batch Operation
Batch Operation
Receiving Batch Data from the SNA host
SOF
Transmitting Batch Data to the SNA Host
STX
ETX
Batch Printer Operation
Batch Operation
Batch Default Options
Customer Option a
1ST Char from VDU Device Indicator
LU Address
BIT 7 Terminate Message to VDU on 1-END of Chain
LU Address not Used
Inbound LU XFR
Char Option not Used
Customer Option C
Application Options
Default CRT = Ascii STANDARD, VT100
Default Kybd = Standard
C5D3 = Lear Siegler ADM 3A
END of Options
Battery RAM
Maintenance
Software Upgrade and Eprom Replacement
System/Line Gen for Batch
Vpacing =
Transfer = Modetab = Instinclm
Sscpfm = Ussscs
Addr = C1
Istatus = Active
Setupmsg Setupinf
Usstab = Rjeincdt
Buffact =
Cctl
Waitime =
Operator
Ckptlns =
Nosep Select = PUNCH1
Operator Cctl Ckptlns =
Cmpct Comp
Nohold Nosep Start
Ifacea Lowspeed
Pudest = Pulcl Punode Xeonode =
Adiscon Codea Comp Ebcdic
Transp
Modeent LOGMODE=BUF256,FMPROF=X’03’,TSPROF=X’03’
Prtrans = YES
Modeent LOGMODE=BUF512,FMPROF=X’03’,TSPROF=X’03’
Compact Modeent LOGMODE=COMPACT,FMPROF=X’03’,TSPROF=X’03’
Ussparm PARM=LOGMODE,DEFAULT=MOCOMP
Ussparm PARM-APPLID,DEFAULT=JES2
Ussparm PARM=LOGMODE,DEFAULT=BATCH
Usscmd CMD=RMT101,REP=LOGON,FORMAT=BAL
Troubleshooting Problems and Odd Installation Problems
Problem Symptom Possible Remedies
Troubleshooting Problems and Odd Installation Problems
Appendix a 3274 SNA Communication Operations
Appendix a 3274 SNA Communication Operations
Appendix B General 3770 SNA Communication Operations
Appendix B General 3770 SNA Communication Operations
Appendix C Conversion Charts
Appendix C Conversion Charts
Protocol Converter Model A/S-4
Appendix C Conversion Charts
Protocol Converter Model A/S-4
Recv Conv
Protocol Converter Model A/S-4
Park Drive Lawrence, PA