PROTOCOL CONVERTER MODEL A/S-4
The Verify Switch Settings menu allows 2 operations as described below:
A.Exit - By entering the letter A the A/S-4 will return to the Main Menu.
B.Restart With New Switch Options - When a B is typed and he A/S-4 will start over, just like the power has been turned off and then on. When the A/S-4 goes through power up, all switches displayed in the menu will be read and serviced.
The Verify Switch Settings menu will display any change in the switches in the menu. The change in the switch should be followed by the Restart command B to insure that the change has been acted upon.
NOTE
The Verify Switch Settings menu will be displayed when running with the A/S-4 PC card, but the switches have no effect on the program running in the PC card because there are no switches on the PC card, so the values displayed for the switches is actual data read from the PC memory.
6.14 Reload Default Options
By selecting item K from the main menu (Section 6.3), the operator obtains the screen shown in Figure 19 which in turn can change all the options in the A/S-4 to their defaults. Entering any character other than a “Y” will return to the main menu without changing any options, if a “Y” is entered the A/S-4 will go through its power up routine as if the power to the unit was turned off and then on.
Reload Default Options
If sure type Y (ALL PAST WORK WILL BE LOST!)
Figure 19
Refer to section 8.4 of Batch operation for the A/S-4’s default options settings.
Protocol Converter Model A/S-4
FCC Statement
Protocol Converter Model A/S-4
Trademarks
Contents
Contents
General Information
General Information
Indicators Power
Specifications
Terminal Automatic Speed Detection
Installation
1General Installation
Modem Interface
Synchronizer
Power Transformer
Carrier Detect
Switches
Terminal Switches
CLEAR-TO-SEND
REQUEST-TO-SEND
Baud Rate
Devices
How to Set Terminal Port Switches for Different Devices
Modem Switches
REQUEST-TO-SEND
How to Set Modem Port Switches for Different Devices
Option Switches
LED Indicator
Power Up
Power Up and Configuration Menu Operations
Type Home for VDU Match or Space Version
Power Up Message
A/S-4 Main Menu
Current
Protocol Converter Main Menu RUN no Changes Else Change VDU
Switching from A/S-4’s Main Menu to Running the Application
Protocol Converter Model A/S-4
Current
Changing the VDU Type
VDU = NEW VDU
Changing VDU Commands for the VDU Type Selected
Changing Video Attributes and Commands for VDU
ESC X Y Z
4 Standard Keyboard Layout
Power Up and Configuration Menu Options
ADM 1178 Keyboard Layout
IBM 3101 Keyboard Layout
PNS Keyboard Layout
Changing Keyboard Layout Type
Protocol Converter Model A/S-4
ESC or =PF20
PA Keys
CTL Z or
Protocol Converter Model A/S-4
Changing Application Options
Changing Application
Do not set the VDU and PRT LU addresses to the same values
XON/XOFF=OFF
Changing Batch Application Options
Printer Options
Current
Power Up and Configuration Menu Options
Programmable Printer Options
Verify Switch Settings
Reload Default Options
Interactive Operation
Batch Operation
Receiving Batch Data from the SNA host
Batch Operation
SOF
Transmitting Batch Data to the SNA Host
STX
ETX
Batch Printer Operation
Batch Operation
Batch Default Options
BIT 7 Terminate Message to VDU on 1-END of Chain
1ST Char from VDU Device Indicator
LU Address
Customer Option a
Customer Option C
Inbound LU XFR
Char Option not Used
LU Address not Used
C5D3 = Lear Siegler ADM 3A
Default CRT = Ascii STANDARD, VT100
Default Kybd = Standard
Application Options
END of Options
Battery RAM
Maintenance
Software Upgrade and Eprom Replacement
System/Line Gen for Batch
Addr = C1
Transfer = Modetab = Instinclm
Sscpfm = Ussscs
Vpacing =
Buffact =
Setupmsg Setupinf
Usstab = Rjeincdt
Istatus = Active
Ckptlns =
Waitime =
Operator
Cctl
Nohold Nosep Start
Operator Cctl Ckptlns =
Cmpct Comp
Nosep Select = PUNCH1
Transp
Pudest = Pulcl Punode Xeonode =
Adiscon Codea Comp Ebcdic
Ifacea Lowspeed
Compact Modeent LOGMODE=COMPACT,FMPROF=X’03’,TSPROF=X’03’
Prtrans = YES
Modeent LOGMODE=BUF512,FMPROF=X’03’,TSPROF=X’03’
Modeent LOGMODE=BUF256,FMPROF=X’03’,TSPROF=X’03’
Usscmd CMD=RMT101,REP=LOGON,FORMAT=BAL
Ussparm PARM-APPLID,DEFAULT=JES2
Ussparm PARM=LOGMODE,DEFAULT=BATCH
Ussparm PARM=LOGMODE,DEFAULT=MOCOMP
Problem Symptom Possible Remedies
Troubleshooting Problems and Odd Installation Problems
Troubleshooting Problems and Odd Installation Problems
Appendix a 3274 SNA Communication Operations
Appendix a 3274 SNA Communication Operations
Appendix B General 3770 SNA Communication Operations
Appendix B General 3770 SNA Communication Operations
Appendix C Conversion Charts
Appendix C Conversion Charts
Protocol Converter Model A/S-4
Appendix C Conversion Charts
Protocol Converter Model A/S-4
Recv Conv
Protocol Converter Model A/S-4
Park Drive Lawrence, PA