Note: IF either the Auger Motor, or Mixer Motor, or Solenoid Error Screen appear: The entire system is inoperable this means that one of either the Auger Motor, or Mixer Motor, or Solenoid [Dispense Valve] is not functional while that Hopper Status in ON. To continue operating the other Hoppers: Go into Program Mode [by pressing simultaneously the Rinse and Stop keys], Press RINSE to get the HOPPER STATUS screen, Press ▼or ▲key to set the non-functional HOPPER STATUS to OFF; Wait at least 10 sec., then Exit program. Reset Power Switch [OFF and ON].

10.High Temperature Lockout Screen

Definition – This screen is displayed when the present water temperature is 10 °F above the water temperature set point.

Possible Causes: Faulty/disconnected Temperature Sensor.

11.Over Temperature / Over Flow Error Screen

Definition – This screen is displayed and the system is shut down when the present water temperature is sensed higher than 208 °F.

Possible Causes: Faulty/disconnected Over-Temperature/Over-Flow Sensor.

12.Communications Error Screen

Definition – This screen is displayed and the system is shut down when the Communications Link between the Display Board and the Control Board has been interrupted for more than five seconds and then re-established.

Possible Causes: Faulty connection between the Display Board and the Control Board .

13.Communications Failure Screen

Definition – This screen is displayed and the system is shut down when the Communications Link between the Display Board and the Control Board has been interrupted for more than five seconds.

!SYSTEM ERROR!

TEMP SENSOR

!SYSTEM ERROR!

OT/OF SENSOR

!SYSTEM ERROR! COMMUNICATIONS

!SYSTEM ERROR!

COM FAILURE V 1.4

Possible Causes: Faulty connection between the Display Board and the Control Board.

TESTS

1) Water Inlet Valve Test

Turn power off. If the water level rises inside the tank, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire line cord to the terminals. Plug it into a 115V outlet. If water flows in and stops when you pull it out, the Valve is working fine. Repeat this test a few times. The problem may be in the Probe. If the water does not flow in when the cord is plugged into an electrical outlet, the Solenoid coil may be damaged, opened or the valve may have an obstruction preventing the water from flowing in. Clean or replace it.

A Check Valve is installed to prevent backflow.

To check proper function of Check Valve, disconnect water line from the Check Valve, check for dripping from the disconnected end of the Check Valve. If it leaks replace it.

2)Water Level Probe Test

If there is a lack of water, you will get an error message on the LCD window. Check the probe as follows:

Turn on the power and water supply. Check inside the tank to make sure the water is not touching the Probe. Pull the wire and terminal out of the Probe rod. If water starts flowing into the tank, the Probe may be grounded, due to excessive liming. Check with Ohm meter. Clean or replace.

3)Relay Test

Turn Power Switch ON.

Measure Voltage across Output “COM” to Ground. Should read 120 V. Measure Voltage across Input “NO” to Ground. Should read 120 V. Measure Voltage across Input to Coil . Should read 24 VDC.

CHECK VALVE

ASS’Y L463A

HOSE NUT

ASS’Y K178A

WATER INLET

VALVE L462A

16

Page 15 Page 17
Page 16
Image 16
Cecilware GB-IT operation manual Tests, Over Temperature / Over Flow Error Screen, Communications Error Screen
Page 15 Page 17

GB-IT specifications

The Cecilware GB-IT is a cutting-edge coffee brewing system designed to cater to the needs of cafes, restaurants, and other commercial establishments that require efficiency, speed, and quality in coffee production. This machine stands out for its robust construction and the use of advanced technologies, making it a reliable choice for high-demand environments.

One of the primary features of the Cecilware GB-IT is its dual-purpose capability, functioning as both an automatic brewer and a tea brewer. This versatility allows businesses to serve a wide range of hot beverages without needing multiple machines, ultimately saving space and reducing operational costs. The GB-IT has a generous brewing capacity, typically handling up to 3 gallons of coffee in a single batch, which is essential for busy service periods.

The machine is equipped with a unique digital brew control that allows users to set precise brew times and temperatures. This feature ensures that each cup of coffee is brewed to perfection, providing a consistent flavor profile that loyal customers can rely on. Additionally, the GB-IT comes with programmable volumes, allowing operators to customize the amount of coffee brewed based on their specific needs and customer demand.

Another notable characteristic of the Cecilware GB-IT is its durable construction. Built with high-quality stainless steel, the machine not only has an appealing aesthetic but is also designed to withstand the rigors of daily use in a bustling commercial environment. Its compact footprint allows it to fit seamlessly into any kitchen setup, maximizing counter space while still delivering high performance.

The GB-IT also incorporates advanced safety features, including an automatic shut-off system that activates when the water reservoir runs low or the brewing cycle is complete. This thoughtful design minimizes the risk of overheating and ensures the longevity of the machine.

In terms of maintenance, the Cecilware GB-IT is designed for easy cleaning and servicing, with components that can be easily accessed. This ensures that operators can perform routine maintenance without significant downtime, contributing to overall operational efficiency.

In summary, the Cecilware GB-IT stands as an excellent solution for businesses that prioritize quality, efficiency, and versatility in their beverage offerings. With its advanced features, durable construction, and user-friendly design, it is a worthwhile investment for any establishment looking to elevate their coffee and tea service.
Top Page Image Contents