Manuals / Cecilware / Kitchen Appliance / Hot Beverage Maker

Cecilware GB-IT operation manual To Replace The Picture / Duratran, Inside Door, S Go S

Models: GB-IT

1 34

Download 34 pages 11.82 Kb

Page 18

Image 18

PICTURE / DURATRAN REPLACEMENT and BULB AND STARTER REPLACEMENT - ILL. D

To Replace The Picture / Duratran:

Lift up the two end tabs on top of door with a pointed object or flat head screwdriver. Pull the entire picture frame out. Open up the two clear panels and replace picture. Tuck clear plastic panel inside bracket at top.

BE SURE TO TUCK CLEAR PANEL UNDER

BRACKET BEFORE SLIDING FRAME ASS'Y

INSIDE DOOR.	S GO S
O G

To replace the Fluorescent Bulb:

Remove the inside door panel.

Turn the lamp and pull it out of the lamp holder, then place the new lamp into the lamp holder and turn it until it snaps into position.

To replace the Starter: Remove the inside door panel. Turn the starter slightly counter- clockwise and take it out of the starter base.

To install the new starter, snap the starter into the starter base and turn it slightly clockwise into position.

Page 18

Image 18

Cecilware GB-IT To Replace The Picture / Duratran, Be Sure To Tuck Clear Panel Under Bracket Before Sliding Frame Assy

Contents

CAPPUCCINO, COFFEE, and SOUP DISPENSERS GB-IT Intelligent Technology Cecilware sells value... WorldwideVolts MECHANICAL SPECIFICATIONSINSTALLATION INSTRUCTIONS WattsFOR CAPPUCCINO START-UP PROCEDURETO CHECK VOLUME AND GRAM THROW DISPENSED RATIO FOR COFFEEBACK VIEW GB3M-5.5-IT DIMENSIONS & CONPONENTS LOCATION - ILL. AFRONT VIEW RIGHT SIDE VIEWADJUSTMENTS - ILL. B Features and Benefits of the Digital Dispenser Controller PARAMETER DEFINITIONS FOR SYSTEM SOFTWARE VERSION Page MODES OF OPERATION To access SERVICE MODE - Press simultaneouslyPROGRAMMING INSTRUCTIONS - ILL. C INITIALIZING MODEFunctions Teach Me Timer SetupPROGRAM MODE “portion control”Functions SERVICE MODEGeneral Conventions HOPPER STATUSMIXER START TIME #.# SEC AUGER STOP TIME SELECT A KEY AUGER STOP TIME GRAM THROW SELECT A KEY GRAM THROW ### AUGER START TIME SELECT A KEYAUGER START TIME #.# SEC MIXER START TIME SELECT A KEY #.# SEC MIXER STOP TIME SELECT A KEY MIXER STOP TIME #.# SECRESET SYSTEM COMPLETED RINSE LOCKOUT ## HRS WATER TEMP ### DEG FLOW TEMP LOCKOUT ### DEG F Initialization Screen High Temperature Lockout ScreenDEFINITION OF SCREENS DURING NORMAL OPERATION Low Water Level Screen2. Water OverflowError Screen DEFINITION OF ERROR SCREENS AND TROUBLESHOOTING1. Over Temperature Error Screen 4. No Temperature Response Error Screen12. Communications Error Screen 10. High Temperature Lockout Screen11. Over Temperature / Over Flow Error Screen TESTS1. CHECK ALL DISPENSE VALVES FOR LIME BUILD-UP RECOMMENDED PREVENTIVE MAINTENANCE3. CLEAN OUT VENT MOTOR, TROUGH AND TUBING 2. CHECK ALL CHAMBER MOUNTS FOR SIGNS OF WEARINSIDE DOOR To Replace The Picture / DuratranBE SURE TO TUCK CLEAR PANEL UNDER BRACKET BEFORE SLIDING FRAME ASSY S GO SCleaning the Hoppers See Illustration E SANITIZING, CLEANING AND REFILLING HOPPERSCleaning Removing and Cleaning the Whipper Chambers See Illustration EHOPPER CD144 HOPPER and DISPENSING CHAMBER ASSYS WITH WIRE AUGERS - ILL. EHOPPER COVER CD106 HOPPER CD152HOPPER and DISPENSING CHAMBER ASSY WITH NYLON AUGERS - ILL. E WHIPPER BLADE CD143 or CD64APROBABLE CAUSE TROUBLESHOOTING GUIDEPROBLEM REMEDYTANK ASS’Y - ILL. F 15. Noise cominga Hopper not properly engaged in back, or DESCRIPTION ILL. GDOOR ASS’Y WITH COMPONENTS GB3M5.5 IT SHOWN GB3M-10-ITDESCRIPTION AND LOCATION OF COMPONENTS GB3M5.5 IT SHOWN ILL. H GB3M-10-IT GBM-5.5-IT COMMON PARTS IDENTIFICATION LISTDESCRIPTION TRANSFORMER C-CLASS use w/DC motor CD151Page Page Page Page Page Page USING OLDER VERSION OF TOUCH PAD WITH ONE RIBBON CONNECTOR USING OLDER VERSION OF TOUCH PAD WITH ONE RIBBON CONNECTOR

To Replace The Picture / Duratran:

BE SURE TO TUCK CLEAR PANEL UNDER

INSIDE DOOR.

S GO S

To replace the Fluorescent Bulb: