Runco CX-46HD, CX-40HD manual Using Picture-In-Picture PIP

Page 54

Operation

4.5 Using

Picture-In-Picture (PIP)

To use PIP, press the PIP () button.

The PIP window appears inside the main image window.

Press PIP again to switch to side-by-side PIP mode.

Press PIP again to turn PIP off.

ASPECT SIZE POSITION PIP

S.SWAPTV/AV

TIMER

OFF

2. Press the (

44	Runco CX-40HD/CX-46HD Owner’s Operating Manual

Image 54

Contents CX-40HD CX-46HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Crystal Series LCD Display at a Glance Controls and IndicatorsControls and Functions SpeakersCrystal Series LCD Display Inputs and OutputsHDMI2/Computer Input Digital INPUT3 Component Video RCA connectorsINPUT4 Component Video RCA connectors PC Audio InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlNumeric Buttons Memory Preset ButtonsOFF / on Source Selection ButtonsLetbox Letterbox Aspect Ratio Selection Buttons ANA 169 Anamorphic4X3 Standard Vwide VirtualWideSurrnd Surround Timer OFF ButtonSound Control Buttons MTS/SAP Multichannel Television Sound/Second Audio ProgramControls and Functions Installation Remote ControlBattery Installation Quick Setup Installation OverviewStep Procedure For Details, refer to Ambient Light Installation ConsiderationsWall-Mounting the Crystal Series LCD Display Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionHdmi Connections Rear of the Display Rear of the PC DVD/DTV STB AV OUT Connections Connecting External Speakers OptionalConnecting to a Dolby 10. Digital Audio ConnectionConnection Connector Pin AssignmentsRS-232 Controller Rear PanelInstallation Changing the OSD Language Turning on the PowerOperation Flashes for a few seconds, then lights solidSetting the PC Display Properties Using the On-Screen Menus Setup Picture AdjustTimer SourceAspect Ratio Main MenuSource 169 Letterbox VirtualWideAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Adjust Picture Adjust Brightness Contrast Color Tint SharpnessBacklight Color Temp Gamma Save Settings Restore Settings Typical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Channel Auto Tuning Add/Erase Favorite Channel ChannelTimer Setup Characteristics of the incoming signalFCC Ratings and Content Categories Rating/Category DescriptionRating/Category Description Sexual content Operation ISF Calibration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetUsing Picture-In-Picture PIP Available Main and PIP Source Combinations PIP Input SourceButton on the remote control Changing the PIP AspectRatio To 169 or vice versa, press the Aspect Stereo Sound/SAP Swapping the Main and PIP ImagesSwapping the Main PIP Audio Programs Mono+SAP Broadcast Mode Receive Mode Mono StereoCompatibility with Stereo and SAP Audio Broadcasts Stereo+SAPTroubleshooting Chart Maintenance and TroubleshootingTroubleshooting Tips Symptom Possible Causes SolutionComputer Signal Serial Commands RS-232 Connection and Port ConfigurationSerial Command Syntax Command DescriptionSAB SDB Key 0105 0054 Serial Communications Specifications Crystal Series LCD Display SpecificationsCrystal Series LCD Display Specifications Weight Regulatory Approvals Limited Warranty Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CX-40HD DimensionsView Signal Mode Vertical Horizontal Computer Signal CompatibilityComputer/Video Signal Compatibility Chart Type Frequency Hz Frequency kHzSpecifications Page Runco CL-810 Owner’s Operating Manual