Zenith warranty Clone Programmer Learning Setup, Learn Setup from Master L20V54S

Page 43

Clone Programmer Learning Setup

Learning the Master TV Setup

Instructions for the Clone Programmer to Learn the Master L20V54S Setup.

Use MPI Cable to Connect LT2002 Clone Programmer to Master L20V54S MPI Port

If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.

Learn Setup from Master L20V54S

Press 1 to select the “LEARN FROM TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” you want to store the master L20V54S’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master L20V54S’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master L20V54S’s setup.

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)

Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability.

After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)

*Note: When using the clone programmer for teaching or learning,

be sure that the heartbeat pattern is shown on the LEDs. Both learning and teaching should take about 45 or more seconds depending on the complexity of the master setup. While the clone is functioning, do not move it or otherwise disturb the clone or wiring connections. If the clone finishes the function in less than 45 seconds, redo the function again. Press the reset button if the clone does not act normally.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

XX

THE TV IS VERSION

XX

THE SW IS REVISION

XX

CLONE CLOCK=

XX:XX

TV CLOCK=

XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

This menu should appear by itself after the LT2002 is connected to the L20V54S MPI port.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

LT2002 Clone Programmer Communication Problems

•A slow flashing green light indicates there are communication problems between the L20V54S and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

•If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries.

P A G E 4 3

Page 42 Page 44
Image 43
Page 42 Page 44
Contents B l e o f c o n t e n t s Installer quick setup guide Installation and Operating Guide WarrantySerial no Record the Model NumberMillbrook Drive Lincolnshire, IL 60069, USA. Phone ComplianceNEC National Electrical Code Important Safety InstructionsTable of Contents Setup Checklist Audio / Video 1, 3 Installation/Connections OverviewTypical Pedestal Type Mount with Swivel Bracket Vesa Standard TV MountsConnect an off-air antenna to the LCD TV/Monitor Antenna HookupMini glossary Connect cable service to the LCD TV/Monitor Cable Service HookupG E 1 Connect antenna and a VCR to the LCD TV/Monitor Antenna & VCR HookupLocate the Antenna/Cable jack on the back of the VCR Connect cable service and a VCR to the LCD TV/Monitor Cable Service with VCR HookupPillow Speaker Interface Controlling the TV with Mechanical SwitchesPillow Speaker Hook Up Controlling the TV with Serial DataAC Power Cord TV Operation Using the front control panel to operate the LCD TV/MonitorRemote Control Sensor and/or Alarm mode Front Panel ControlsDescriptions of the menus and on-screen displays On-Screen Menus OverviewInfo Other Menus & On-Screen DisplaysUser Remote Control Key Functions Installer Remote Control Key Functions Auto Program Channel Search After the channel search, remove unwanted channels Channel ListRemoving unwanted channels Channel Labels Setup Channel Labels SetupOperating the Channel Label Menu On-Off Timers Setup Clock SetupEnter button Installer can set the Time Zone Time Zone SettingsDaylight Saving Choose a language for the on-screen menus Menu LanguageOK Enter button ChipUse the Up/Down/Left/Right arrows buttons to choose Set up the menu options for Tvpg RatingUse the Up/Down/Left/Right arrows buttons to choose To highlight the Setup menuSet up the menu options for Mpaa Rating Press the OK Enter buttonCanadian English Ratings Set up the menu options for Canadian English RatingSet up the menu options for Canadian French Rating G E 3To highlight the Caption menu Use the Down ADJ arrow to highlight Analog ModeCaption Menu Also turn closed captions onOption Font Size, Font Style, Foreground Color etc ServiceTo highlight the Caption menu Use the D / E / F / G ADJ buttons to customize eachOK Enter button Set up the audio options for the end userAdjust the speaker balance for optimum sound quality Sound MenuYou can set digital audio language Using External SpeakersUp/Down/Left/Right arrow buttons to set your own set Tings for the options. When finished, press the OKPicture Menu Use the F / G ADJ buttons to choose Manual and useUser can choose preset formats for the picture Inactive TV Display Channel Bank Managing the Channel BanksProgram package Channel Bank Number Display= Delete Examples of typical channel banks chars filledBasic Extend Other = Active110 111 112 113 114 115 Channel Number Purpose100 Channel Number 101 102 103 104Typical Installer Menu G E 4 Commercial Mode SetupTurn to the next page to continue Cloning Setup Cloning Connections/Learning SetupIf batteries are removed, the Clone Clock time will be lost Learn Setup from Master L20V54S Clone Programmer Learning SetupSet the Clock Optional Teach Master L20V54S’s Setup to the target Cloning Connections / Teaching SetupDisconnect L20V54S Power for 15 Seconds Installer Menu Items 000 through Installer MenuAccessing the Installer’s Menu Using the Installer’s MenuCH not Avble Installer Menu Items 035 throughInstaller Sequence Detailed Descriptions of Installer Menu ItemsFeature Level Mute DisableScan Mode Sleep TimerAtsc Band Detailed Descriptions of Installer Menu ItemsAUX Status Quick ShutoffStart Minor Channel Reference TV Features / Menus that can be ClonedAtsc Tune Mode G E 5Changing Source Labels on Master TV Adding Channel Icons and Labels in the 2-5-4 + Menu ModeTo Do Channel Editing/Labeling, proceed as follows Changing/Adding Channel Labels on Master TVDetailed Instructions Reference Detailed Information For Making a Master TVReference Software Version Check Procedure to Check Software VersionSoftware Problems L20V54S Aux Input Configuration / TroubleshootingSome quick and easy tips to resolving problems Symptoms Possible Causes Possible SolutionsTroubleshooting Reset Clone After Static Shock Reference Cloning Procedure TroubleshootingClone Programmer Troubleshooting Controller Quick Check Clone Troubleshooting Flow ChartTV Operation Check OHM RF Cable Glossary of TermsG E 6 Installer Quick Setup GuideQuick Setup Guide For Integrated Master TVs See table of contents for more informationG E 6 G E 6 G E 6 OWNER’S Responsibility For Customer Support/Service Please callCopyright 2007 LG Electronics U.S.A., Inc LG’S Responsibility
Top Page Image Contents