Zenith DTV1080 warranty Power-Cord Protection, Outdoor Antenna Grounding, Lightning

Page 4

Ground

Clamp

Electric Service Equipment

Figure. 1

Antenna Lead-in Wire

Antenna Discharge Unit

NEC Section 810-20

Grounding Conductors

NEC Section 810-21

Ground Clamps

Power Service Grounding

Electrode System

NEC Art 250, Part H

13. Power-Cord Protection

Route power-supply cords so they are not likely to be walked on or pinched by items placed upon or against them, paying particu- lar attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Outdoor Antenna Grounding

If an outside antenna or cable system is con- nected to this product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (USA), ANSI/NFPA 70, provides information on grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit

connection to the grounding electrodes, and requirements for the grounding electrode. (See Figure.1 on reverse side for an example).

15. Lightning

For added protection for this product during a lightning storm, or when product is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect antenna or cable system. This will prevent damage to product due to lightning and power line surges.

206-3675

3

Image 4

Contents Warranty High Definition HD Satellite ReceiverDo not Open Important Safety Instructions Outdoor Antenna Grounding Power-Cord ProtectionLightning Power Lines Damage Requiring ServiceReplacement Parts Safety CheckImportant Information Table of Contents EZ Help Reference Introduction New World of Digital EntertainmentMain Features Sending Signals Important OverviewTV Signal Formats Signal Format Analog NtscNormal and Wide Format Signals Letter boxCropped SqueezedNormal WidePanorama Zoom1Audio Signals Digital Audio SignalsAnalog Audio Signals On-Screen Display Main MenuEZ Help Remote Control Cables 6 items Setup and ConnectionsReceiver Unpacking Back Panel of the Zenith HD Satellite Receiver Back Panel of the Zenith HD Satellite Receiver General Recommendations Connection ComponentConnecting to Antennas No Dish Receiving SignalsConnecting to Antennas Round Dish Satellite a Connecting to Antennas Oval Dish Satellite A, B Connecting to Antennas Oval Dish Satellite A, B, C TV Connection Analog TV TV ViewingTV Connection HD Monitor Y/PB/PR type TV Connection HD Monitor RGB type VCR Connection Refer to .5, ‘Connecting to TV’VCR Recording Audio Connection Digital Audio System Dolby AC-3 ConnectionAudio connection Analog Hi-Fi System Hi-Fi System ConnectionUsing the Front Panel of the HD satellite receiver Using the Remote Control ModeDigit Buttons 0~9 DashSignal MuteVol + CH +Surf InfoHelp ? Thumbstick Menu directional arrowsProgramming the Remote Control Test your remote controlRemote Control Codes for Other Components TV CodesVCR Codes DVD CodesAUX Audio Initial Setup Basic Operation Viewing the Channel BannerRating CategoryInput Source Icon Lock IconAlternate Audio Mail IconChannel Surfing 206-3675 Press the Guide button on your remote control Advanced Program GUIDEAbout the Advanced Program Guide To bring up the APGLayout of the Advanced Program Guide Screen AllCustom Surf Movies SportsMoving through the Advanced Program Guide Line ScrollingScrolling Date ScrollingSelecting a Program Current / Free-of-ChargeFuture / Free-of-charge Current / Pay Per ViewGetting More Information To display program detailsReferring to EZ Help Making a Remind List for Future Viewing To schedule a future viewingPurchasing Pay Per View Programs To purchase PPV programsSearching Programs by Category To search programs by CategorySearching Programs by Keyword To search programs by keywordCustomization Structure of the On-screen MenusTo bring up and exit the Menu To go to the next levelDigital Output Audio Mode Audio Variable Audio Language AudioTo cancel a program in the Remind List Previewing the Remind ListManaging Program Purchases To cancel a newly purchased programNew Purchase Purchase List To review programs in the Purchase ListChecking the Mail Box To check the Mail BoxAbout Initial Setup Initializing the SystemSelect Dish To select dishYour Location To enter your locationSignal Strength To see the signal strengthTo scan the channels from the satellites Channel SetupRepeat from 6 to EZ Channel Scan Channel Search Managing ChannelsTo scan the channels with the antenna Manual Ch. Add To add the channels missed in your channel listEdit Channel To create a custom listManaging Channels EZ Hook Up To see EZ Hook-upClock Auto Setting the ClockTo set auto clock Clock Manual To set manual clockSetting Digital Output Setting the AudioTo set the digital audio mode PCMDigital Dolby DigitalAudio Mode To Set the Analog Audio ModeAudio Language To set the digital audio languageVariable Audio To set Variable AudioChoosing the Aspect Ratio Choosing the screen format of your TVLetter Box Setting Closed Caption To set Closed CaptionCaption1 CC1 Caption2 CC2Caption3 CC3 Caption4 CC4Output Channel Setting Default Signal OutTo set the channel number of the HD satellite receiver Out to TV -- Default Connection To set the standby mode default signal sourceTo set the standby mode as a default signal source Setting the Digital TV InputDigital TV Input Running EZ Demo To run EZ DemoLock System Setting LocksTo activate or deactivate the Lock System Block Channel To block channelsMovie Rating To block movie programsTo block TV programs TV Rating for Children’s ProgramsTV-MAMature Audience Only TV Rating for General Programs Spending Limit To set the spending limit of each PPV programTesting the System To test the HD satellite receiverTo upgrade the software in your Zenith HD Satellite Receiver Upgrading SoftwareReplace Card To replace the cardEZ Help EZ HelpSimply press and hold to see the helpful information See the EZ Help feature Product Specifications InputAudio Features Troubleshooting Make sure the batteries are fresh and installed properly Point the remote control unit at the remote control sensorCheck if a mode on the remote control is selected properly Them to clear your passwordZenith Electronics Corporation 6owz7 oenwnw No 3828VA0220B ND00QA, SH-011S