Winegard RD-4610 owner manual Specifications, Model RP-4200 Thick Roof KIT Available

Page 15

SPECIFICATIONS

Height when raised

37" max.

Height in the travel position

12.0" max.

Operating radius

17" (34" diameter circle)

Roof space required

19.5" x 46.75"

LNB

Compatible with DSS® and DISH NetworkTM

Color

White

Satellite antenna height

20.9"

Satellite antenna width

19.5"

F/D

0.59

Offset angle

24o

Frequency range

10.95 - 12.75 GHz

Satellite antenna gain:

 

11.2 GHz

33.22 dBi

12.1 GHz

33.89 dBi

12.6 GHz

34.23 dBi

Aperture efficiency

73%

Cross polarization (on axis)

-21 dB

*Beamwidth at -3 dB

3.5o

*Beamwidth at -10 dB

7.0o

RS-100 antenna gain

 

VHF

15.5 dB avg.

UHF

19.5 dB avg.

RS-1000 antenna height

3.25"

RS-1000 antenna width

14.5"

Wind loading

Up to hurricane force

Weight

19 lbs. max.

Shipping weight:

21 lbs.

DSS® is a registered trademark of DIRECTV, Inc. a unit of Hughes Electronics Corporation.

DISH NetworkTM is a trademark and a service mark of EchoStar Communications Corporation.

MODEL RP-4200 THICK ROOF KIT AVAILABLE

Winegard Company makes available Model RP-4200 which includes one directional handle extension and elevating shaft worm gear assembly. The RP-4200 is designed for roofs more than 4 3/4" to 6 3/4" thick. Contact Winegard Company if roof thickness measures more than 6 3/4". Refer to the table below for the correct directional handle and elevating shaft measurements. Remember to glue extensions (PVC glue is recommended) and handle together after checking that you have the correct length.

ROOF

ELEVATING

W/RW-1000

DIRECTIONAL

Extension

THICKNESS

SHAFT LENGTH

 

HANDLE LENGTH

 

 

 

 

 

 

6 3/4"

8 1/4"

8 3/4"

5 1/8"

2 1/4"

6 1/2"

8"

8 1/2"

7 1/8"

Not Required

6 1/4"

7 3/4"

8 1/4"

6 7/8"

Not Required

 

 

 

 

 

6"

7 1/2"

8"

6 5/8"

Not Required

5 3/4"

7 1/4"

7 3/4"

6 3/8"

Not Required

5 1/2"

7 "

7 1/2"

6 1/8"

Not Required

5 1/4"

6 3/4"

7 1/4"

5 7/8"

Not Required

 

 

 

 

 

5"

6 1/2"

7"

5 5/8"

Not Required

 

 

 

 

 

Rev 1/2001

Printed in U.S.A. Winegard Company • 3000 Kirkwood Street • Burlington, Iowa 52601-2000 © Winegard Company, 2001 2451142 Rev. 6/05/01 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Winegard Install Point Base Toward Front VehicleInstallation & Assembly Antenna Shown Partially Raised For Ease of Illustration only Except for screw indicated in Figure Inside RV Point to Front of RV Approximately Degrees from Travel PositionDirectional Handle Travel PositionElevation OperationPosition Except Travel Position DO’S Tuning Antenna for Best PictureWatching OFF-AIR TV Lowering Antenna to Travel PositionVCR Lubricating Rubber Quad Ring MaintenanceElevating Shaft & Worm Gear Assembly Replacement Procedure Mount LubricationAntenna does not or is Hard to Rotate Trouble Shooting No PictureWarranty Repair Work Ordering Repair PartsRear View Parts ListNot to Scale Crank Handle KIT RK-HAND Parts List Interior Hardware KIT RK-CEILModel RP-4200 Thick Roof KIT Available SpecificationsRev
Top Page Image Contents